Filter
Top Products
-4-
,(+(5+<5+,9:;(5+;/,;6634(5<(3(5+
;/,:,05:;9<*;065:-69;/,<:,6-;/0:;()3,
>0;/@6<996<;,9 Failure to follow all
instructions listed below may result in serious
personal injury.
"573<.;663),-69,:,;;05.<705;()3,
4(205.(+1<:;4,5;:69*/(5.05.)0;:
Accidental start-up of the tool can cause
injury.
<33@ (::,4)3, (5+ ;0./;,5 (33 ;/,
-(:;,5,9:9,8<09,+-69;/0:;()3,(5+
46<5;05.;/,96<;,9Also remember to
occasionally check the stand and make sure
it is still tight. A loose stand is unstable and
may shift in use and cause serious injury.
,-69,67,9(;05.4(2,:<9,;/,,5;09,<50;
0:73(*,+65(:630+-3(;3,=,3:<9-(*,
Serious injury could occur if tool is unstable
and tips.
,=,9:;(5+65;/,;()3,69<:,(:3(++,9
69:*(--63+05. Serious injury could occur if
the table is tipped or the cutting tool is
accidentally contacted. Do not store
materials on or near the table such that it is
necessary to stand on the table or its stand
to reach them.
,=,9<:,+<3369+(4(.,+)0;: /(97
)0;:4<:;),/(5+3,+>0;/*(9, Damaged
bits can snap during use. Dull bits require
more force to push the workpiece, possibly
causing the bit to break.
(;*/;/,(7796790(;,)0;(5+0;::7,,+;6
@6<9(7730*(;065656;<:,)0;:;/(;
/(=,(*<;;05.+0(4,;,9;/(;,?*,,+:;/,
*(7(*0;@6-;/,;663Overloading the tool
can lead to personal injury or tool failure.
,=,9 :;(9; ;/, ;663 >/,5 ;/, )0; 0:
,5.(.,+05;/,4(;,90(3 The bit cutting
edge may grab the material causing loss of
control of the workpiece.
6<;,9)0;:(9,05;,5+,+-69>66+>66+
796+<*;:(5+73(:;0*653@,:<9,;/,
>69270,*,+6,:56;*65;(055(03:,;*
),-69,96<;05. Cutting a nail or the like will
cause the carbides to be dislodged, fly
toward the operator side, and possibly strike
you or bystanders.
,,+;/,>69270,*,(.(05:;;/,96;(;0656-
;/,)0;!/,)0;96;(;,:*6<5;,9*36*2>0:,
(:=0,>,+-964;/,;676-;()3, Feeding
the work in the wrong direction will cause the
workpiece to "climb" up on the bit and may
lead to loss of control during operation.
,=,973(*,/(5+:5,(9;/,:705505.)0;
":,7<:/:;0*2:=,9;0*(3(5+/690A65;(33@
46<5;,+-,(;/,9)6(9+::7905.:;0*2:
(5+6;/,910.:;6/63++6>5;/,>69270,*,
(5+ 2,,7@6<9/(5+:(>(@-964;/,
:705505.)0; Router cuts are blind cuts but
the bit still protrudes through the table and
you must be aware of the position of your
hands relative to the spinning bit.
$,+656;9,*644,5+*<;;05.4(;,90(3
;/(;0:>(97,+>6))3@696;/,9>0:,
<5:;()3,-;/0::0;<(;0650:<5(=60+()3,
(3>(@:*<;;/,4(;,90(3>0;/;/,*65*(=,
:0+,(.(05:;;/,;()3,Cutting the material
with the concave side up or away from table
may cause the warped or wobbly material to
roll; causing you to lose control, kickback and
serious personal injury may result.
":, ;/,(+1<:;()3,-,5*,05:;9(0./;
*<;;05.(7730*(;065: When routing along
an entire edge of the work, the fence, fence
faces, and adjustable outfeed fence support
shims will help maintain stability.
$/,5;/,;()3,0:<:,+>0;/6<;;/,-,5*,
7036;,+)0;:69),(905.)0;:4<:;),
<:,+Piloted bits are used when routing
internal and external contours on a
workpiece. The bearing of the piloted bit
assists in maintaining control of the
workpiece. Whenever possible, the starter
pin should also be used.
(-,;@<3,:-696<;,9!()3,
,=,9;6<*/;/,)0;+<905.69044,+0(;,3@
(-;,9;/,<:, After use the bit is too hot to
be touched by bare hands.
,=,93(@;/,;663+6>5<5;03;/,46;69
/(:*64,;6(*6473,;,:;(5+:;033 The
spinning bit can grab the surface and pull the
tool out of your control.
,=,9 <:, )0;: ;/(; /(=, ( *<;;05.
+0(4,;,9.9,(;,9;/(5;/,67,505.05;/,
)(:,
BM 2610933969 09-12_BM 2610933969 09-12.qxp 9/20/12 9:19 AM Page 4