Filter
Top Products
Utilice apenas la presión suficiente
para evitar que la rectificadora vibre
o rebote. Demasiada presión
disminuirá la velocidad y forzará el
motor. Normalmente, sólo el peso de
la herramienta alcanza para la mayoría
de los trabajos de rectificado. Utilice
poca presión cuando rectifique bordes
mellados o pernos flojos donde existe
la posibilidad de que la rectificadora
se enganche en un borde de metal.
Aleje la rectificadora de la pieza antes
de apagarla.
En las operaciones normales de cepillado
con alambre, el material eliminado y las
cerdas del cepillo se dispararán (hasta
50pies o más) con una fuerza
considerable. Existe la posibilidad de que
ocurran lesiones graves. Para protegerse
contra este riesgo, los operadores y
demás personas en el área de trabajo
deben usar vestimenta de protección
ygafas de seguridad, o protectores para
todo el rostro sobre lasgafas de
seguridad con protección lateral.
!
ADVERTENCIA
Mantenimiento
El servicio de la herramienta debe
ser realizado sólo por personal de
reparaciones calificado. El servicio
o mantenimiento realizado por
personas no calificadas puede provocar
riesgo de lesiones.
Si la herramienta no funciona
correctamente, devuelva la
herramienta a una instalación
de servicios para repararla.
Limpieza
Limpie el polvo y los desechos de
los orificios y contactos eléctricos,
soplando con aire comprimido.
Mantenga los mangos de las
herramientas limpios, secos y libres
de aceite o grasa. Use únicamente un
jabón suave y un paño húmedo para
limpiar la herramienta, evitando todos
los contactos eléctricos.
Ciertos agentes de limpieza y solventes
son nocivos para los plásticos y otras
piezas aisladas. Algunos de éstos
incluyen gasolina, aguarrás, solvente
para laca, solvente de pintura,
solventes de limpieza con cloro,
amoníaco y detergentes de uso
doméstico que contengan amoníaco.
Nunca use solventes inflamables
ni combustibles cerca de las
herramientas.
SERVICIO TÉCNICO
Para obtener información con relación
al funcionamiento o reparación de
este producto, sírvase llamar al
1-800-424-8936.
El servicio de la herramienta debe
serrealizado sólo por personal de
reparaciones calificado. El servicio o
mantenimiento realizado por personas
no calificadas puede provocar riesgo
delesiones.
!
PRECAUCION
19 Sp
DG470500CK
General Safety
Information (Cont’d.)
3. Do not wear loose fitting clothing,
scarves, or neck ties in work area.
Loose clothing may become caught
in moving parts and result in serious
personal injury.
4. Do not wear jewelry when
operating any tool. Jewelry may
become caught in moving parts and
result in serious personal injury.
5. Always use attachments designed
for use with this tool. Do not use
damaged or worn attachments.
6. Never trigger the tool when not
applied to a work object.
Attachments must be securely
attached. Loose attachments can
cause serious injury.
7. Never point a tool at oneself or any
other person. Serious injury could
occur.
8. Use steady, even pressure when
using tool. Do not force. Too much
pressure can cause grinding wheel
to break or overheat.
9. Keep all nuts, bolts and screws tight
and ensure equipment is in safe
working condition.
10.Do not put hands near or under
moving parts.
11.Always use proper guard with
grinding wheel. The guard protects
operator from broken wheel
fragements.
12.Accessories must be rated for at
least 11,000 RPM. Wheels and other
accessories running over rated
speed can fly apart and cause injury.
13.Grinding wheel and guard must be
securely attached as described in
this operating manual before
connecting the grinder to a power
source.
14.Grinding wheels must be stored in a
dry place.
15.Before attaching the grinding
wheel, inspect it for visible defects.
If cracked, chipped, or warped, do
not install it.
16.Do not overtighten the clamp nut
on the grinding wheel. Excessive
tightening can cause the wheel to
crack during operation.
17.Make sure that the guard is in good
condition and securely installed
before operating grinder.
18.Do not clamp the grinder in a vise
or use as a fixed grinder.
19.Never turn on the grinder with the
grinding wheel or any rotating
parts touching the workpiece.
20.Use only grinding wheels in
compliance with ANSI standard B7.1
and rated greater than 11,000 RPM.
21.Do not use the grinder if the disc
flange or clamp nut is missing or if
the spindle is bent.
WORK AREA
Do not
operate a power tool in an
explosive atmosphere, such
as in the presence of flammable liquids,
gases, or dust. Power tools create
sparks which may ignite the fumes or
dust.
Keep work area
clean and well lighted. Cluttered
benches and dark areas invite
accidents.
Keep bystanders,
children, and visitors away while
operating a power tool. Distractions
can cause you to lose control.
ELECTRICAL SAFETY
Do not expose
power tools to rain or wet conditions.
Water entering a power tool will
increase the risk of electric shock.
Avoid body contact
with grounded surfaces such as pipes,
radiators, ranges, and refrigerators.
There is an increased risk of electric
shock if your body is grounded.
Do not abuse cord.
• Never carry tool by its cord.
• Never pull the cord to disconnect
from receptacle. Pull plug at the
outlet.
1. Do not operate tool with damaged
cord or plug.
• Have a damaged or worn power
cord and/or strain relief replaced
immediately.
• Do not attempt to repair power
cord.
2. Make sure cord is located so that it
will not be stepped on, tripped
over, or otherwise subjected to
damage or stress.
3. Do not use an extension cord unless
absolutely necessary. Use of
improper extension cord could
result in a risk of fire and electric
!
WARNING
!
WARNING
!
WARNING
!
CAUTION
!
CAUTION
!
WARNING
shock. If an extension cord must be
used, make sure:
• That the pins on plug of extension
cord are the same number, size and
shape as those of plug on tool cord.
• That the extension cord is
properly wired and in good
electrical condition.
• If an extension cord is to be used
outdoors it must be marked with
the suffix “W-A” or “W” following
the cord type designation to
indicate it is acceptable for outdoor
use. For example – SJTW-A
4. Do not expose cord to rain, snow or
frost.
PERSONAL SAFETY
Do not misuse this
product. Excessive exposure to
vibration, work in awkward positions,
and repetitive work motions can cause
injury to hands and arms. Stop using
any tool if discomfort, numbness,
tingling, or pain occur, and consult a
physician.
1. Stay alert, watch what you are
doing, and use common sense when
operating a power tool. Do not use
tool while tired or under the
influence of drugs, alcohol, or
medication. A moment of
inattention while operating power
tools may result in serious personal
injury.
Avoid accidental
starting. Be sure switch is in the locked
or off position before plugging in the
tool. Carrying tools with your finger on
the switch or plugging in a tool with
the switch on invites accidents.
2. Remove adjusting keys or wrenches
before turning on the tool. A key or
wrench attached to a rotating part
of the tool may result in personal
injury.
3. Do not overreach. Keep
proper footing and
balance at all times.
Proper footing and
balance enable better control of the
tool in unexpected situations.
4. Always work in a well-ventilated
area. Wear an OSHA-approved dust
mask and safety glasses.
5. Hold tool by insulated gripping
surface when performing an
operation where the tool may
contact hidden wiring. Contacting a
“live” wire will make exposed metal
parts of the tool “live” and shock
the operator.
!
CAUTION
!
WARNING
2
www.chpower.com
Operating Instructions and Parts Manual
Para Ordenar Repuestos o Asistencia Técnica, Llame al Teléfono 1-800-424-8936
Sirvase darnos la siguiente información:
- Número del modelo
- Código impreso
- Descripción y número del repuesto según la lista de repuestos
Número del
Descripción Repuesto
Dirija toda la correspondencia a:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
Lista de Repuestos
Disco de rectificado para metal de 4,5" (115 mm) DG027700AV
Mango lateral DG027800AV
Llave de 2 dientes DG026600AV
Calibre del cable 18 18 16 14 14 12 12 10 10
Cables de extensión para rectificadora de 4 1/2" (115 mm)
Longitud del cable (pies) 25 50 100 150 200 250 300 400 500
Funcionamiento
(Continuación)