Filter
Top Products
2
Operating Instructions and Parts Manual
General Safety
Danger means a
hazard that will
cause death or serious injury if the
warning is ignored.
Warning means a
hazard that could
cause death or serious injury if the
warning is ignored.
Caution means a
hazard that may
cause minor or moderate injury if the
warning is ignored. It also may mean a
hazard that will only cause damage to
property.
NOTE: Note means any additional
information pertaining to the product
or its proper usage.
Read all instructions and safety
precautions before operating the unit.
Risk of fire or explosion!
Solvent and paint fumes
can explode or ignite,
causing severe injury and
property damage.
Paints and solvents containing
HALOGENATED HYDROCARBONS can
react explosively with aluminum.
Always check the product’s label
before using these materials in the
unit.
Make sure the room is well-ventilated.
Avoid all ignition sources, such as static
electricity sparks, open flames, hot
objects, sparks from connecting and
disconnecting power cords, and
working light switches.
Follow the material and solvent
manufacturers’ safety precautions and
warnings. Do not use liquids with flash
points less than 100 degrees Fahrenheit
(38 degrees Celsius).
Do not carry TURBINE while spraying.
Keep the turbine at the maximum
distance from the spraying area.
Static electricity can be produced by
HVLP spraying. Make sure any
electrically conductive object being
sprayed is grounded to prevent static
sparking. The sprayer is grounded
through the electric cord. If an
extension cord is necessary, the cord
!
WARNING
!
CAUTION
!
WARNING
!
DANGER
must be a grounded, 115 volt, three
wire type cord.
Hazardous vapors: Paints,
solvents, insecticides, and
other materials may be
harmful if inhaled,
causing severe nausea,
fainting, or poisoning.
Use a respirator or mask whenever
there is a chance that vapors may be
inhaled. Read all instructions with the
mask to ensure that the mask will
provide the necessary protection
against the inhalation of harmful
vapors.
NEVER point the spray gun at any part
of the body, or at anyone else.
Tipping the gun causes the gun to clog.
Dried spray material also clogs the
pressure delivery tube and fittings. The
spray gun does not function when
clogging occurs.
When not in use, be sure to disconnect
the hose and place the gun on a solid,
level surface to avoid tipping.
GROUNDING INSTRUCTIONS
This product must be properly
grounded. In the event of an electrical
short circuit, grounding reduces the risk
of electrical shock by providing an
alternate path for the electrical current.
This product is equipped with a cord
that has a ground wire and an
appropriate ground plug. Plug the unit
into an outlet that is properly installed
and grounded in accordance with local
codes and ordinances.
Improper installation of
the ground plug can
result in the risk of
electrical shock. If repair
or replacement of the plug or cord is
necessary, do not connect the ground
wire to either flat blade terminal. The
wire with green insulation (with or
without a yellow stripe) is the
grounding wire.
1. For any question regarding proper
installation of the ground plug,
consult a qualified (licensed or
certified) electrician.
!
DANGER
!
CAUTION
2. Do not modify the plug provided. If
the plug does not fit the outlet,
have the proper outlet installed by a
qualified electrician.
3. This product is for use on a nominal
120-volt circuit and has a grounding
plug that looks like the plug in
Figure 2. Make sure that the
product is connected to an outlet
having the same configuration as
the plug. No adapters should be
used with this product.
Figure 2 - Grounding Plug
4. If an extension cord is required, use
only a three wire extension cord
that has the same configuration as
the unit cord, including the (round)
ground terminal. Make sure that
the extension cord is plugged into a
properly grounded receptacle.
5. When using an extension cord, be
sure it is in good condition and
heavy enough to meet the
specifications in the chart below. If
an extension cord is needed, the
following wire sizes must be used
(See Chart 1).
Chart 1 Extension Cord Requirements
For Information About
This Product
Call 1-800-626-4401
25’ cord . . . . . . . .10,12, or 14 Gauge
50’ cord . . . . . . . . . . .10 or 12 Gauge
100’ cord . . . . . . . . . . . . . . .10 Gauge
TEST
RESET
Grounding
Pin
www.chpower.com