Filter
Top Products
I
I
I
I
SAFETY RULES FOR TILE WET SAWS cont.
6. NEVER try to cut freehand. Make sure that the tile to be cut is pressed firmly
against the rip fence.
7. NEVER cut pieces too small to be held securely against the fence without
leaving enough space for your hand to be a safe distance from the blade.
8. NEVER cut more than one tile at a time.
9. KEEP the saw table free of clutter with the exception of the tile you are cutting.
10. MAKE SURE that the work piece that will be cut off has enough room to move
sideways. Failure to do so may result in the off-cut binding against the blade.
11. BEFORE cutting a tile piece, let the saw blade run freely for a few seconds.
If it makes an unfamiliar sound or vibrates excessively, switch it off immediately
and disconnect from the power supply.
12. PULL blade/cutting assembly slowly and smoothly through the tile being
cut. NEVER leave the tool running unattended. Turn power off.
13. LET the blade come to a complete stop before removing any jammed or off-cut
material from around the blade area.
14. KEEP the water tray topped off with water at the correct level. Allowing the blade
to run dry may cause the diamond blade to overheat.
15. ALWAYS wear protective gloves when handling the blade or any accessories.
Blades and accessories may be hot after prolonged use.
ADDITIONAL RULES FOR SAFE OPERATION
Z_WARNJNG: BE SURE to read and understand all instructions. Failure to
follow all instructions listed below may result in electric shock, fire and/or serious
personal injury.
1. KNOW your power tool. Read the operator's manual carefully. Learn the
applications and limitations, as well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric shock, fire or serious injury.
2. WEAR SAFETY glasses or eye shields when using this saw. Everyday
eyeglasses have only impact-resistant lenses; they ARE NOT safety glasses.
3. PROTECT your lungs. Wear a face mask or dust mask ifthe operation isdusty
4. PROTECT your hearing. Wear appropriate personal hearing protection during
use. Under some conditions and duration of use, noise from this product may
contribute to hearing loss.
5. ALL VlSTORS AND BYSTANDERS MUST wear the same safety equipment that
the operator of the saw wears.
6. INSPECT the tool cords periodically and if damaged have them repaired at
your nearest Sears Service Center or other Authorized Service Facility.
7. ALWAYS check the tool for damaged parts. Before further use of the tool, a
guard or other part that is damaged should be carefully checked to determine if it
will operate properly and perform its intended function.
10
ADDITIONAL RULES FOR SAFE OPERATION cont.
8. DO NOT abuse the cord, NEVER use the cord to carry the tool or pull the
plug from the outlet. Keep cord away from heat, oil, sharp edges or moving
parts. Replace damaged cord immediately. Damaged cords increase the risk of
electric shock.
9. SAVE THESE iNSTRUCTIONS. Refer to them frequently and use them to instruct
others who may use this tool. If someone borrows this tool be sure to provide
them with this owner's manual.
AWARNING: Some dust particles created by power sanding, sawing,
grinding, drilling and other construction jobs contain chemicals known to
cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending upon how often you do
this type of work. To reduce your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
='0| = - = e
Rating
Input
Output
No-Load Speed
Blade Diameter
Depth Of Cut
Outer Dimensions
Net Weight
120V, 60 Hz AC
6.7 Amps
11/15-Peak HP
3550 rpm
7-in. (33 mm)
1-in.
(LWH) 379/10-in. X 171/2-in. X 441/2-in.
76 LBS.
NOTE: Before attempting to use any tool, be sure to familiarize yourself with all|
i
the operating features and safety instructions.
J
J J
Z_WARNING: DO NOT let familiarity with your saw make you careless.
Remember that a careless fraction of a second is sufficient to cause severe injury.
11
I
I
I
I
1-19-06