Filter
Top Products
Hereare examples
of what a SEARS
Craftsmantool can
do...
Sharpen Tools
Cawe Wood
Precise Ddliing Shape Wood
[
Deburr Metal
Cut Metal
_The operation of any power
toot can result in foreign
objects being throwninto the eyes, which can
result in severe eye damage Always wear
safety glasses or eye shields before com-
mencing power tool operation, We
recommend Wide Vision Safety Mask for use
over spectacles or standard safety glasses
Whenever you hold the tool,be careful not to
cover the air vents with your hand This blocks
the air flow and causes the motor to overheat
_ Always unplug rotary tool
before changing acces-
sories, changing collets or servicing your
rotarytoolo
COLLET -- To loosen, first press shaft lock
button and rotate the shaft by hand until the
lock engages the shaft preventing further
rotation.
,,..,o0,
\ TOTIfiHTEN
\ t C0LLEr
_._ --L_ --'_ NUT
-
TOLOOSEN COLLET
_Do not engage loci( while
the Rotary Tool Is running.
With the shaft lock engaged use the coilet
wrench to loosen the collet nut if necessary
Change accessories by inserting the new one
into tl_e collet as far as possible to minimize
runout and unbalance. With the shaft lock
engaged, finger tighten the coflet nut until the
accessory shank is gripped by theco!let Avoid
excessive tightening of the collet nut The
collet system is a superior method of seeudng
accessoi3es
COLLETS _ Two different size coliets (see
illustration),to accommodate different shank
sizes, are available for your Rotary Tool, To
instatl a different cofiet, remove the cotlet nut
and remove the old colleL Insert the unslotted
end of the coltet in the hole inthe end of the
tool shaft,, Replace coIIet nut on the shaft.
Always use the collet which matches the
shank size of the accessory you plan to
uSe,rNever force a larger diameter shank into
a coltst
COLLETIDENTIFICATIONCHART-- Coltetsizesc-_
beidentifiedby therings ontheback endof eollet I
1/32" Co[lethas one(t) ring |
!/16" Collethas two (2) rings |
3/32"Cotlefhasthree(3) rings |
1/8" CoHethasno rings J
/
/
118"COLLET 25037
3/32"COLLET
BALANCING ACCESSORIES -- For
precision work, it is important that all
accessories be in good ba;ance (much the
same as the tires on your automobile} To true
up or balance an accessory, slightly loosen
collet nut and give the accessory or collat a 1/4
turn. Retighten coflet nut and nJn the Rotary
Tool. You should be able to teff by the sound
and feel if your accessory is running m
balance. Continue adjusting in this fashion
until best balance is achieved To maintain
balance on abrasive wheel points, before each
use, with the wheel point secured in the co]let,
turn on the Rotary Tool and run the Dressing
Stone lightly against the revolving wheel point
This removes high spots and trues up the
wheel point for good balance
Do not use grinding
wheels over 1" in dia-
meter. Rotary Tool's high speed can cause
larger wheels to fly apart and could cause
injury,
SAFETY -- Protect your eyes when grinding
or routing with the Rotary Toof .always wear
an approved type ofsafety glasses
Remember, your new Sears RotaryTool is the
finest power tool of its kind But its
performance is only as good as the
accessories with which it is used. We
recommend only Sears accessories be used.
Use of any other accessories may create a
hazard We hope you'll enjoy many years of
trouble free pleasure from your Sears
Craftsman Rotary PowerTool
USE ONLY RECOMMENDED ]
ACCESSORIES
Page 3