Filter
Top Products
6
The abrasive is simply pressed onto the sanding
pad and pulled off again after use.
Please note: Use only abrasives with an
undamaged Stickfix hook-and-loop coating.
Before use, check that the coating has not been
damaged by incorrect use (e. g. overheating).
Please note: The Mini-Stickfix D 52 sanding
pad was developed for use in confined spaces
and with small areas. This small-diameter pad
and the affixed abrasive will inevitably heat up
in use more than larger pads, since the same
pressure is distributed over a smaller area. Sand
only with moderate pressure and do not sand
continuously for too long. Lift the sander off
the workpiece at intervals to allow friction heat
to dissipate.
Working with the tool
Electronic control position:
Material to be sanded, work operation
6:
Sanding hard GRP components (limited
suitability).
3 - 6:
Sanding off dry, cracked paint.
Stripping anti-fouling paints.
Sanding wood.
2 - 4:
Sanding paint/varnish with tendency to smear.
Light sanding of thin top coats of paint.
Cleaning sandstone, concrete, formwork
materials.
1 - 2:
Sanding thermoplastic materials.
Smoothing treated woods with sanding brush.
Maintenance and care
Always remove the plug from the
mains supply socket before doing any work on
the tool!
Any maintenance or repair work requiring the
motor housing to be opened may only be carried
out by an authorized service workshop.
Maintenance or repair work carried out by an
unauthorized person can lead to the wrong
connection of the power leads or other
components, which in turn can lead to accidents
with serious consequences.
Always keep the tool and especially the
ventilation slots clean.
The tool is fitted with special motor brushes
with an automatic cut-out. When the brushes
become worn the power supply is shut off
automatically and the tool comes to a standstill.
Accessories, tools
For safety reasons, only use ori-
ginal Festool accessories and tools!
The accessory and tool order number can be
found in the Festool catalog or on the Internet
under www.festool.com.
Warranty
Conditions of 1+2 Warranty
You are entitled to a free extended warranty (1
year + 2 years = 3 years) for your Festool power
tool. Festool shall be responsible for all shipping
costs during the first year of the warranty.
During the second and third year of the warranty
the customer is responsible for shipping the tool
to Festool. Festool will pay for return shipping
to the customer using UPS Ground Service. All
warranty service is valid 3 years from the date
of purchase on your receipt or invoice.
Festool Limited Warranty
This warranty is valid on the pre-condition that
the tool is used and operated in compliance with
the Festool operating instructions. Festool
warrants, only to the original consumer
purchaser, that the specified tool will be free
from defects in materials and workmanship for
a term of one year from the date of
procurement. Festool makes no other warranty,
express or implied, for Festool portable power
tools. No agent, representative, distributor,
dealer or employee of Festool has the authority
to increase or otherwise change the obligations
or limitations of this warranty. The obligations
of Festool in its sole discretion under this
warranty shall be limited to the repair or
replacement of any Festool portable power tool
that is found to be defective as packaged with
the User Manual.
Excluded from coverage under this warranty
are: normal wear and tear; damages caused
by misuse, abuse or neglect; damage caused
by anything other than defects in material and
workmanship. This warranty does not apply to
accessory items such as circular saw blades,
drill bits, router bits, jigsaw blades, sanding
belts, and grinding wheels. Also excluded are
wearing parts, such as carbon brushes,
lamellas of air tools, rubber collars and seals,
sanding discs and pads, and batteries.
Festool portable power tools requiring
replacement or repair are to be returned with
the receipt of purchase to Festool (call 800-
554-8741 for address details).
IN NO EVENT SHALL FESTOOL BE LIABLE
FOR ANY CONSEQUENTIAL OR