Filter
Top Products
Spray Tip Selection Chart
30 311001G
Spray Tip Selection Chart
Spray Tips, for use with AA Series Air Cap
AAM Fine Finish Spray Tips
Recommended for high finish quality applications at low and medium pressures. Order desired tip
(Part No. AAMxxx) from matrix below.
GG4 Industrial Spray Tips
Recommended for high wear applications at high pressures. Order desired tip (Part No. GG4xxx) from matrix below.
* Tips are tested in water.
† These tip sizes include a 150 mesh tip filter.
‡ Do not use these tips with Model G15 guns (288844).
★ GG4 tips only.
• All tips in the Spray Tip Selection Chart below
can be used with Model G40 guns (249242).
Use tips in the gray shaded area of the chart
with Model G40 guns only.
• Do not use tips in the gray shaded area of the
chart with Model G15 guns (288844).
SKIN INJECTION HAZARD
Do not use tips in the gray shaded area of the Spray
Tip Selection Chart with Model G15 guns (288844).
Failure to follow this warning can result in serious
injury or amputation.
Orifice Size in.
(mm)
* Fluid Output, fl oz/min (lpm) Maximum Pattern Width at 12 in. (305 mm)
at 600 psi
(4.1 MPa, 41 bar)
at 1000 psi
(7.0 MPa, 70 bar)
2 to 4
(100)
4 to 6
(150)
6 to 8
(200)
8 to 10
(250)
10 to 12
(300)
12 to 14
(350)
14 to 16
(400)
16 to 18
(450)
18 to 20
(500)
† 0.007 (0.178) 4.0 (0.1) 5.2 (0.15) ★107 207 307
† 0.009 (0.229) 7.0 (0.2) 9.1 (0.27) 109 209 309 409 509
† 0.011 (0.279) 10.0 (0.3) 13.0 (0.4) 111 211 311 411 511 611
0.013 (0.330) 13.0 (0.4) 16.9 (0.5) 213 313 413 513 613 713
0.015 (0.381) 17.0 (0.5) 22.0 (0.7) 215 315 415 515 615 715 815
0.017 (0.432) 22.0 (0.7) 28.5 (0.85) 217 317 417 517 617 717 817 917
0.019 (0.483) 28.0 (0.8) 36.3 (1.09) 219 319 419 519 619 719 819 919
0.021 (0.533) 35.0 (1.0) 45.4 (1.36) 321 421 521 621 721 821 921
‡ 0.023 (0.584) 40.0 (1.2) 51.9 (1.56) 423 523 623 723 923
‡ 0.025 (0.635) 50.0 (1.5) 64.8 (1.94) 425 625 725 825
‡ 0.027 (0.686) 58.5 (1.7) 75.8 (2.27) 527 627 827
‡ 0.029 (0.737) 68.0 (1.9) 88.2 (2.65) 629
‡ 0.031 (0.787) 78.0 (2.2) 101.1 (3.03) 431 631
‡ 0.033 (0.838) 88.0 (2.5) 114.1 (3.42) 633 ★833
‡ 0.035 (0.889) 98.0 (2.8) 127.1 (3.81) 435
‡ 0.037 (0.940) 108.0 (3.1) 140.0 (4.20) 737
‡ 0.039 (0.991) 118.0 (3.4) 153.0 (4.59) 539 639 839
Fluid output (Q) at other pressures (P) can be calculated by this formula: Q = (0.041) (QT)
where QT = fluid output (fl oz/min) from the above table for the selected orifice size.
P