Graco Inc. GC-1392 Z Paint Sprayer User Manual


  Open as PDF
of 42
 
Start-Up
Gel-Coat
1. Open ball valve at material regulator.
2. With the roller cam still unattached from slave pump
OLQNDJHDUPVORZO\EHJLQWRGLDOXSSUHVVXUHDW
material regulator. Between 5-15 psi, the pump will
EHJLQWRF\FOH7KHSXPSZLOOFRQWLQXHWR¿OOWKHV\V
tem with material and will stall out when the polyes-
ter arrives at the gun.
• 0DWHULDOYLVFRVLW\WHPSHUDWXUH¿OOHUORDGVXUIDFH
tension and other factors will ultimately determine the
proper material pressure that will be required.
• GlasCraft recommends an initial start-up pressure of
20-25 psi.
3. Dial up material pump pressure to initial start-up
pressure.
4. Prime the slave pump to proper psi. depending on
which gun is being used.
5. Rotate Pivot Knob, P/N SSP-159 to Re-engage
catalyst drive arm.
7KHUHPD\EHDVPDOODPRXQWRIDLUVWLOOLQWKH
PDWHULDO,WZLOOSXVKLWVHOIRXWTXLFNO\
6.&KHFNDQGFRQ¿UPWKHIROORZLQJSRLQWV
&RQ¿UPWKDW\RXDUHJHWWLQJDFRPSOHWHFRQVLVWHQWDQG
uniform mix of catalyst. If red dye catalyst is being used,
WKLVZLOOEHHDV\WRFRQ¿UPYLVXDOO\
• While triggering the gun onto a test panel, visibly inspect
WKHÀXLGSUHVVXUHJDXJHRQWKHFDWDO\VWSXPS
• The catalyst pressure should approximately match the
ÀXLGSUHVVXUHJHQHUDWHGE\WKHPDWHULDOSXPS
([DPSOH
:LWKSXPSGLDOHGXSWRSVLDWWKHUHJXODWRU\RX
ZLOOKDYH[ SVLÀXLGSUHVVXUH
:LWKSXPSGLDOHGXSWRSVLDWWKHUHJXODWRU\RX
ZLOOKDYH[ SVLÀXLGSUHVVXUH
• While spraying the gun, inspect catalyst pressure gauge
WRFRQ¿UPFDWDO\VWSUHVVXUH
• Because of material viscosity, size of nozzle, hose length
and other factors, the catalyst pressure may not exactly
exactly match material pressure.
• Catalyst pressure should be +/- 50 psi of material
pressure.
7.$IWHUFRQ¿UPLQJDFFHSWDEOHFDWDO\VWWRPDWHULDOSUHVVXUH
VSUD\VHYHUDOWHVWVWULSVRUSDQHOVWRFRQ¿UPJHOWLPHDQG
uniform catalization. Catalyst pressure should stay
consistent and steady.
8. Inspect material dispense pattern.
9. Adjust material pressure to achieve desired pattern of
material.
10.6ROYHQWÀXVKWKHJXQ
,WLVLPSRUWDQWWRUHPHPEHUWKDWDIWHUUHOHDVLQJWKH
trigger, mixed catalyst and material will remain in the
KHDGRIWKHJXQ'HSHQGLQJRQWKHJHOWLPHRIWKH
PDWHULDOLQDUHDVRQDEO\VKRUWSHULRGRIWLPHLWZLOOEH
QHFHVVDU\WRPull the trigger and begin spraying
DJDLQ256ROYHQWÀXVKWKHJXQ
GC-1392Z 15
 previous next