Grizzly G9972Z Lathe User Manual


  Open as PDF
of 76
 
"&)"
<..,'O&&m'+AVi]Zl$<ZVgWdm
Te st Run
DcXZ i]Z VhhZbWan ^h XdbeaZiZ! iZhi gjc ndjg
bVX]^cZidbV`ZhjgZ^igjchegdeZgan#
>[! Yjg^c\ i]Z iZhi gjc! ndj XVccdi ZVh^an adXViZ
i]ZhdjgXZd[VcjcjhjVacd^hZdgk^WgVi^dc!hide
jh^c\ i]Z bVX]^cZ ^bbZY^ViZan! i]Zc gZk^Zl i]Z
TroubleshootingdcPage 45#
>[ndjhi^aaXVccdigZbZYnVegdWaZb!XdciVXidjg
IZX]HjeedgiVi*,%*)+".++([dgVhh^hiVcXZ#
To test run the machine:
1. BV`ZhjgZndj]VkZgZVYi]ZhV[Zin^chigjX"
i^dchVii]ZWZ\^cc^c\d[i]ZbVcjVaVcYi]Vi
i]ZbVX]^cZ^hhZijeegdeZgan#
2. GZVY VcY jcYZghiVcY i]Z Basic Controls
hjWhZXi^dcdcPage 16#
3. BV`ZhjgZVaa iddahVcYdW_ZXihjhZYYjg^c\
hZijeVgZXaZVgZYVlVn[gdbi]ZbVX]^cZ#
4. EZg[dgb Vaa ajWg^XVi^dc egdXZYjgZh Vh
^chigjXiZY ^c i]Z Lubrication hjWhZXi^dc dc
Page 41#
6. 8dccZXii]ZbVX]^cZidi]ZedlZghdjgXZ#
7. A^[i i]Z XdkZg d[ i]Z bdidg DC$D;; hl^iX]
VcYijgci]ZbdidgON#
8. ;a^e i]Zhe^cYaZ hl^iX] idi]Z g^\]i Redh^"
i^dc·i]Zhe^cYaZh]djaYgdiViZcounterclock-
wise VcY i]Z aZVYhXgZl h]djaY ijgc clock-
wise#
Note: Listen to and watch for abnormal
noises or actions. The machine should run
smoothly with little or no vibration or rubbing
noises.
Strange or unusual noises should be inves-
tigated and corrected before operating the
machine further. Always disconnect the
machine from power when investigating or
correcting potential problems.
9. ;a^ei]Zhe^cYaZhl^iX]idi]ZXZciZgOedh^"
i^dc VcY lV^i [dg i]Z he^cYaZ id XdbZ id V
XdbeaZiZhide#
10. Ijgc i]Z he^cYaZ hl^iX] id i]Z aZ[i L edh^"
i^dc·i]Zhe^cYaZh]djaYgdiViZclockwiseVcY
i]ZaZVYhXgZlh]djaYijgccounterclockwise#
5. BdkZi]Z]Va["cjiaZkZgjeidY^hZc\V\Zi]Z
]Va["cji!VcYejh]i]ZedlZg[ZZYaZkZgYdlc
id Y^hZc\V\Z i]Z XVgg^V\Z edlZg [ZZY! Vh
h]dlc^cFigure 9#
Check Gearbox Oil
>i^hXg^i^XVai]VindjbV`ZhjgZi]ZgZ^hd^a^ci]Z
[ZZY gViZ \ZVgWdm WZ[dgZ egdXZZY^c\ l^i] i]Z
iZhigjc#GZ[Zgidi]ZLubrication^chigjXi^dchdc
Page 41 [dgbdgZYZiV^ahdcl]^X]ineZd[d^aid
jhZ!]dlbjX]idjhZ!VcYl]ZgZideji^i#
GEARBOXES MUST
BE FILLED WITH OIL!
NO OIL SHIPPED WITH
MACHINE!
Requires ISO 68
or Equivalent
Gear Oil.
NOTICE
ALWAYS make sure the power feed lever
and the half-nut lever are disengaged before
starting the lathe to avoid carriage crashes
with the headstock or tailstock.
Figure 9.=Va["cjiVcYedlZg[ZZYaZkZg
edh^i^dch[dgIZhiGjc#
EdlZg;ZZY
AZkZg9dlc
=dg^odciVa
=Va["CjiAZkZg
Je=dg^odciVa
 previous next