Grizzly G9972Z Lathe User Manual


  Open as PDF
of 76
 
<..,'O&&m'+AVi]Zl$<ZVgWdm
"(&"
4. 8dc[^\jgZi]ZK"WZaidci]ZejaaZnhVXXdgY^c\
id i]Z aZiiZg VcY cjbWZg XdbW^cVi^dcjcYZg
i]ZhZaZXiZYhe^cYaZheZZY[gdbi]ZX]Vgi^c
Figure 36#
Edh^i^dci]Z^YaZgejaaZndcided[i]ZK"WZai
l^i] Zcdj\] YdlclVgY egZhhjgZ id egdk^YZ
iZch^dc id i]Z WZai! i]Zc [jaan hZXjgZ ^i ^c
eaVXZ# I]ZgZ^h XdggZXi iZch^dcidi]Z K"WZai
l]Zc i]ZgZ ^h Veegdm^bViZan
&
¿' YZ[aZXi^dc
l]Zc bdYZgViZ egZhhjgZ ^h Veea^ZY id i]Z
K"WZai]Va["lVnWZilZZci]ZejaaZnh#
Note: The pulley slots are numbered 1–3
with number 1 being the outside slot.
·;dg6¶8Xdc[^\jgVi^dchhZZFigure 37!
edh^i^dci]Zadc\ZgK"WZai('^cX^gXjb[Zg"
ZcXZ^ci]ZXdggZXi8ejaaZnhadi!i]Zcgdaa
^idcidi]Z6ejaaZn#
·;dg7¶8Xdc[^\jgVi^dchhZZFigure 38!
eaVXZ i]Zh]dgiZg K"WZai '.^c X^gXjb[Zg"
ZcXZ^ci]ZXdggZXi8ejaaZnhadi!i]Zcgdaa
^idcidi]Z7ejaaZn#
Power Feed
EdlZg;ZZYdcVaVi]Zh^beanbZVchjh^c\i]Z
bVX]^cZ"Yg^kZcXdbedcZcihid[ZZYi]Zidda^cid
i]Zldg`e^ZXZgVi]Zgi]Vc[ZZY^c\^ibVcjVaanl^i]
]VcYl]ZZah#
I]ZheZZYVil]^X]i]ZXVgg^V\ZigVkZah^hhZil^i]
i]Z [ZZY gViZ Y^Vah hZZ Feed RatedcPage 32
[dg YZiV^aZY^chigjXi^dch! Wji ^i Vahd YZeZcYh dc
he^cYaZheZZY#
NOTICE
Feed rate is based on the spindle speed.
High feed rates result in a rapidly moving
carriage. Pay close attention to the feed
rate you have chosen and keep your hand
poised over the power feed lever. Failure to
fully understand this could cause the car-
riage to crash into the spindle or tailstock
resulting in severe damage to the lathe.
L]Zci]ZegdeZg[ZZYgViZ]VhWZZchZaZXiZY[dg
i]ZdeZgVi^dc!h^beanbdkZi]ZedlZg[ZZYaZkZg
je id Zc\V\Z i]Z XVgg^V\Z l^i] i]Z edlZg [ZZY
hZZ Figure 39# BdkZ i]Z aZkZg Ydlc id Y^hZc"
\V\Zi]ZedlZg[ZZY#
L]Zc i]Z he^cYaZ ^h gdiVi^c\ XdjciZgXadX`l^hZ
idlVgYh i]Z deZgVidg! i]Z XVgg^V\Z l^aa bdkZ
idlVgYi]Zhe^cYaZl]ZcZc\V\ZYl^i]i]ZedlZg
[ZZY# 8dckZghZan! l]Zc i]Z he^cYaZ ^h gdiVi^c\
XadX`l^hZVlVn[gdbi]Z deZgVidg!i]Z XVgg^V\Z
l^aabdkZidlVgYi]ZiV^ahidX`#
Note: If the spindle is not turning, you may have
to manually jog the carriage to engage the apron
gearing with the leadscrew.
NOTICE
NEVER attempt to engage the carriage
power feed (lever up) and the half-nut (lever
down) at the same time. Always disengage
the half-nut (lever up) before moving the
power feed lever up. Otherwise, severe
damage to the lathe could occur.
Figure 39.EdlZg[ZZYaZkZgZc\V\ZYVcY
Y^hZc\V\ZY#
9^hZc\V\ZYD[[
:c\V\ZYDc
 previous next