"('"
<..,'O&&m'+AVi]Zl$<ZVgWdm
Feed Rate
;ZZYgViZ^hi]ZheZZYi]ZiddaigVkZahYjg^c\i]Z
deZgVi^dcVcY^hZmegZhhZY^c^cX]Zhd[XVgg^V\Z
igVkZa eZg gZkdaji^dc d[ i]Z he^cYaZ >EG! VcY ^h
hZiWnXdc[^\jg^c\i]ZX]Vc\Z\ZVghVcY[ZZYgViZ
Y^Vah#
I]Z XdggZXi [ZZY gViZ ^h YZiZgb^cZY Wn i]Z
ldg`e^ZXZbViZg^Va!i]ZineZd[idda^c\jhZY!VcY
i]ZYZh^gZY[^c^h]#I]ZiVWaZ^cFigure 40 h]dlh
i]ZgZXdbbZcYZY[ZZYgViZ[dgijgc^c\bdhibZi"
Vah#
Recommended Feed Rates
Ldg`BViZg^Va
BV\cZh^jb
6ajb^cjb
7gVhh7gdcoZ
8deeZg
8Vhi>gdcHd[i
8Vhi>gdc=VgY
B^aYHiZZa
8VhiHiZZa
IddaHiZZa
6aadnHiZZah=VgY
HiV^caZhhHiZZa
I^iVc^jb
=^BV\VcZhZHiZZa
Idda;ZZYGViZ>EG
Rough Cuts Finish Cuts
%#%&*¶%#%'*
%#%&*¶%#%'*
%#%&*¶%#%'*
%#%&%¶%#%'%
%#%&*¶%#%'*
%#%&%¶%#%'%
%#%&%¶%#%'%
%#%&%¶%#%'%
%#%&%¶%#%'%
%#%&%¶%#%'%
%#%&%¶%#%'%
%#%&%¶%#%'%
%#%&%¶%#%'%
%#%%*¶%#%&%
%#%%*¶%#%&%
%#%%(¶%#%&%
%#%%)¶%#%%-
%#%%*¶%#%&%
%#%%(¶%#%&%
%#%%(¶%#%&%
%#%%(¶%#%&%
%#%%(¶%#%&%
%#%%(¶%#%&%
%#%%(¶%#%&%
%#%%(¶%#%&%
%#%%(¶%#%&%
Note: These values are a guideline only. Refer
to the MACHINERY’S HANDBOOK for more
detailed information.
Figure 40.GZXdbbZcYZY[ZZYgViZiVWaZ#
WV
aZkZg
867
')
'-
'-
(*
-)
,%
,,
,%
>>
>>
>>
>
%#%%''
%#%%(%
%#%%((
%#%%(-
%#%%)*
%#%%+%
%#%%+,
%#%%,,
%#%%.%
%#%&'%
%#%&(*
%#%&*%
W
V
&'%
&',
)*
)*
^ch$
Figure 42.;ZZYgViZX]Vgi[dgedlZg[ZZYbdkZbZcid[i]ZXVgg^V\Z#
The V-belt, change gears,
and pulleys represent
a serious entanglement
hazard when the lathe
is running. Always dis-
connect the lathe from
power before opening
the change gear cover.
JhZFigure 41 id^YZci^[n i]ZX]Vc\Z\ZVghVcY
i]Z^gedh^i^dch#
Note: This lathe is shipped with the 24 tooth gear
installed in the "a" position, and the 84 tooth gear
in the "b" position.
Figure 41.8]Vc\Z\ZVgh#
8]Vc\Z
<ZVgb
E^kdi6gb
8VeHXgZl
8]Vc\Z<ZVg
&'%$&',I
8]Vc\Z
<ZVga