Husqvarna FSA 8400 D Saw User Manual


 
36
FS6600 Diesel Model FS6600
18”
FS6600
26”
FS6600
30”
FS6600
36”
FS6600
42”
FS6600 Diesel Model – CE FS6600
450mm
FS6600
650mm
FS6600
750mm
FS6600
900mm
FS6600
1000mm
ALL SAWS FEATURE:
Blade Guard Capacity - in. (mm)
18 (457) 26 (660) 30 (762) 36 (914) 42 (1,067)
Max. Depth of Cut - in. (mm)
6.50 (165) 10.50 (267) 12.50 (318) 15 (381) 20.50 (508)
Blade Shaft RPM
2,400 1,800 1,600 1,350 1,180
Approximate Blade Shaft HP
60 Horsepower
Arbor Size in. (mm)
1" (25.4) with single drive pin
Quick Disconnect Blade Flange
Diameter – in. (mm)
5
(127)
5
(127)
5
(127)
6
(152)
7
(178)
Blade Shaft Diameter - in. (mm)
2" (51)
Blade Shaft Bearings
Cast Sealed blade shaft with 4 maintenance-free ball bearings
Blade Shaft Drive
Dual 8-groove banded 3VX V-belts (16 grooves total)
Blade Coolant
Zinc plated dual multiple-jet water spray tubes
Blade Guard Attachment
Slip-on through 36" (900mm); Bolt-On for 42” (1000mm), auto-latch
Blade Control
Electro-hydraulic pump raises blade; switch controlled raise/lower on speed control handle;
switch controlled positive depth stop; dial type cutting depth indicator; blade drive
disengagement system (clutch); quick disconnect blade flanges
Axle Front
1.25" (31.75 mm) diameter
Rear
Easy Adjust Center Pivot w/2 Hydraulic Powered Wheel Motors
Wheels Front
8” x 3" x 1" (203mm x 76mm x 25.4mm)
Thick polyurethane tread; sealed ball bearing requiring less maintenance
Rear
10" x 3" x 1.25" (254mm x 76mm x 32mm)
Solid rubber, Quick disconnect
Transmission
Hydrostatic Pump, w/2 Hydraulic Wheel Motors connected with hoses, neutral start switch,
single handle speed control, Hydraulic bypass valve for pushing.
Max. Ground Speed Infinitely variable: 0 – 300 FPM forward & reverse. (25 M/min maximum reverse speed on CE models)
Chassis
Heavy-duty, rigid, box and channel section construction
Weight – lb. (Kg) – Uncrated
1,789 (812) 1,811 (822) 1,832 (831) 1,863 (845) 1,888 (857)
POWER SOURCE:
Engine
John Deere Turbocharged Diesel
Specifications
4024TF270
Max. Horsepower
66 @ 2,800 RPM DIN. (49.2 kW)
Displacement cu. in. (l)
149 cu. in. (2.44 liter)
Bore – in. (mm)
3.39 (86)
Stroke – in. (mm)
4.13 (105)
Cylinders
4
Fuel Capacity – gal. (l)
10 (37.8)
Oil Capacity – qt. (l)
8.5 (8) with filter OR 7.6 (7.2) without filter
Air Filter
Radial Seal with pre-cleaner and restriction indicator
Starter
Electric
Engine Coolant
50/50 Water/Ethyl Glycol Mix
SAW DIMENSIONS w/ 36” (900mm) guard: Inches
Metric
(mm)
A Saw Width 37-3/8 949
B Center to Center Wheel Width (track) – FRONT 24-5/8 625
Center to Center Wheel Width (track) – REAR 25-1/4 642
C Outside to Outside Wheel Width - FRONT 27-5/8 702
Outside to Outside Wheel Width - REAR 28-1/4 717
D Frame Width 29-1/2 749
E Inner Flange to Inner Flange Width 32-1/2 825
F Handle Extension 30 762
G Minimum Saw Length (handles in, pointer up,
guard up)
61 1,550
H Saw Length (pointer up, handles extended) 84 2,133
I Maximum Overall Height (pointer up) 53 1,346
Maximum Overall Height (top of pre-cleaner,
pointer down)
56 1,422
K Minimum Overall Height (no muffler, rotate pre-
cleaner)
49-1/2 1,255
L Wheel Base 24 610
M Guard to Handle Length (handles in) 75 1,905
N Maximum Overall Length (handles in) 106 1/2 2,705
O Maximum Overall Length (handles extended) 129 3,276
FS6600 DIESEL SPECIFICATIONS
Standard & CE Models