Filter
Top Products
9
FFUUNNCCTTIIOONNAALL DDEESSCCRRIIPPTTIIOONN
BBee aawwaarree tthhaatt tthhiiss ttooooll iiss aallwwaayyss iinn aann ooppeerraattiinngg ccoonnddiittiioonn
bbeeccaauussee iitt ddooeess nnoott hhaavvee ttoo bbee pplluuggggeedd iinnttoo aann eelleeccttrriiccaall oouuttlleett..
Always turn
the switch
““OOFFFF””
and remove the battery pack before changing bits.
CCOONNTTRROOLLSS AANNDD
CCOOMMPPOONNEENNTTSS::
1. Battery Pack
2. Release Buttons
on Each Side
3. Charger
4. Indicator Lights
5. Saw Shoe
6. Trigger Switch
7. Rubber Grip
8. Lock-Off Button
AACCCCEESSSSOORRIIEESS:
:
9. Saw Blades (1)
10
WWhheenn rreessttaarrttiinngg aa ssaaww iinn tthhee wwoorrkk ppiieeccee,, cceenntteerr tthhee ssaaww bbllaaddee iinn tthhee kkeerrff aanndd
cchheecckk tthhaatt tteeeetthh aarree n
noott eennggaaggeedd iinnttoo tthhee mmaatteerriiaall..
If saw blade is binding, it may
walk up or KICKBACK from the work piece as the saw is restarted.
SSuuppppoorrtt llaarrggee ppaanneellss ttoo mmiinniimmiizzee tthhee rriisskk ooff bbllaaddee ppiinncchhiinngg aanndd KKIIC
CKKBBAACCKK..
Large
panels tend to sag under their own weight. Supports must be placed under the panel
on both sides, near the line of cut and near the edge of the panel.
DDoo nnoott uussee dduullll oorr ddaammaaggeedd bbllaaddee..
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade binding and KICKBACK.
BBllaaddee ddeepptthh aanndd bbeevveell aaddjjuussttiinngg lloocckkiinngg lleevveerrss mmuusstt bbe
e ttiigghhtt aanndd sseeccuurree bbeeffoorree mmaakk--
iinngg ccuutt..
If blade adjustment shifts while cutting, it will cause binding and KICKBACK.
UUssee eexxttrraa ccaauuttiioonn wwhheenn mmaakkiinngg aa ““PPoocckkeett CCuutt”” iinnttoo eexxiissttiinngg w
waallllss oorr ootthheerr bblliinndd
aarreeaass..
The protruding blade may cut objects that can cause KICKBACK.
SSYYMMBBOOLLSS
IIMMPPOORRTTAANNTT::
Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SSYYMMBBOOLL NNAAMMEE EEXXPPLLAANNAATTIIOONN
V Volts Voltage (Potential)
A Amperes Current
Hz Hertz Frequency (Cycles per Second)
W Watt Power
Kg Kilograms Weight
Alternating Current Type of Current
Direct Current Type of Current
Alternating or Direct Current Type of Current
Earthing Terminal Grounding Terminal
Class II Construction Denotes Double Insulation
min Minutes Time
s Seconds Time
Diameter Size of Drill Bits,
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
1
2
3
4
9
5
6
7
8
CCOOMMPPOONNEENNTT MMOODDEELL NNUUMMBBEERR
BATTERY PACK 690549
CHARGER 690543
SAW BLADES 690576