Filter
Top Products
CCHHAARRGGIINNGG BBAATTTTEERRYY PPAACCKK
CCHHAARRGGEE BBAATTTTEERRYY PPAACCKK::
1. Plug the charger into
the nearest 120 volt
electrical outlet.
2. Make sure the trigger
on the Cordless Drill
is in the
““OOFFFF””
position and remove
the battery pack from
the Cordless Drill.
3. Insert the battery pack into
the charger. Be sure that the
battery pack is fully seated
in the charger.
Do not force.
4. The red indicator light should come
““OONN””
indicating that the battery pack is in
a “Fast Charge” mode. If the green indicator light comes
““OONN””
, then the battery
is already fully charged.
5. After approximately one hour of charging, the red indicator light should go
““OOFFFF””
and the green light should come
““OONN””
indicating that the battery is fully
charged and the charger is now in a “Trickle Charge” mode.
6. The battery can be left in a “Trickle Charge” mode until ready to use.
IIMMPPOORRTTAANNTT
IINNFFOORRMMAATTIIOONN FFOORR RREECCHHAARRGGIINNGG HHOOTT BBAATTTTEERRIIEESS
When using your Cordless Drill continuously, the batteries in your battery pack
will become hot. You should let a hot battery pack cool down for approximately
30 minutes before attempting to recharge. When the battery pack becomes
discharged and is hot, the red light on the charger will flash. When the battery
pack cools down, the red light will glow continuously to indicate fast charging
mode, 1-hour charge time.
TThhiiss wwiillll ooccccuurr wwhheenn ccoonnttiinnuuoouuss uussee ooff yyoouurr CCoorrddlleessss
DDrriil
lll ccaauusseess tthhee bbaatttteerryy ppaacckk ttoo bbeeccoommee hhoott..
It does not occur under normal
circumstances.
14
RREEMMOOVVIINNGG // AATTTTAACCHHIINNGG BBAATTTTEERRYY PPAACCKK
RREEMMOOVVEE BBAATTTTEERRYY PPAACCKK::
1. Press both release
buttons on either
side of the Cordless
Circular Saw to release the
battery pack.
2. Pull battery pack free of
Cordless Circular Saw.
AATTTTAACCHH BBAATTTTEERRYY PPAACCKK::
1. Align the raised portion of
the battery pack with the
groove in the
battery compartment of
the Cordless Circular Saw.
2. Press the battery pack into
place. Make sure the latch-
es are securely fastened. Do not use the Cordless Circular Saw if the battery
pack is not seated properly.
CCHHAARRGGEERR
BBeeffoorree uussiinngg bbaatttteerryy cchhaarrggeerr,, pplleeaassee rreeaadd ccaarreeffuullllyy aallll
iinnssttrruuccttiioonnss aanndd ccaauuttiioonnaarryy mmaarrkkiinnggs
s oonn bbaatttteerryy cchhaarrggeerr,, bbaatttteerryy ppaacckk aanndd
pprroodduucctt uussiinngg bbaatttteerryy..
UUssee oonnllyy tthhee cchhaarrggeerr wwhhiicchh aaccccoommppaanniieedd
yyoouurr pprroodduucctt oorr ddiirreecctt rreeppllaacceemmeenntt aass
lliisstteedd iinn tthhiiss mmaannuuaall..
Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
DDoo nnoott ddiissaasssseemmbbllee cchhaarrggeerr..
DDoo nnoott u
ussee cchhaarrggeerr iiff iitt hhaass bbeeeenn ddaammaaggeedd,, lleefftt oouuttddoooorrss iinn tthhee rraaiinn,, ssnnooww,, wweett
oorr ddaammpp eennvviirroonnmmeennttss,, oorr iimmm
meerrsseedd iinn lliiqquuiidd..
TThhee bbaatttteerryy ppaacckk aanndd cchhaarrggeerr hheeaatt dduurriinngg cchhaarrggiinngg..
Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
WWhheenn tthhee bbaatttteerryy ppaacckk rreeqquuiirre
ess rreecchhaarrggiinngg,, aa 11 hhoouurr cchhaarrggee aalllloowwss tthhee ttooooll ttoo
ooppeerraattee aatt ffuullll ppoowweerr..
A charging indicator light on the charger will illuminate to
show that charging is taking place.
13
RELEASE
BUTTON
BATTERY PACK
LED
LIGHT
BATTERY
CHARGER