Lincoln Electric 10A Welder User Manual


 
Power Feed 10A Controller
www.lincolnelectric.com
[7]
RECOMMENDED OPTIONS
GENERAL OPTIONS
Power Feed 10SFM Motor
Conversion Kit
Used to convert NA-series wire drives
into PF-10S wire drives. Includes an
ArcLink™ motor retrofit kit used to
replace existing motor on NA-3, 4 or 5
wire feed head. For use with NA-series
gear head.
Order K2311-1
ArcLink Cable (5-pin)
Includes two leads plus two mating
terminals. Connects Power Feed 10A
controller to Power Wave AC/DC 1000.
Order K1543-XX
Flux Hopper for Tandem Arc
Flux Hopper for K387 mountings.
Order K389
Feeder Control Cable (14-pin)
Connects Power Wave AC/DC 1000 to
wire feeder.
Order K1785-xx
Contact Nozzle Assembly
Single arc contact nozzle assembly for
1/8" (3.2 mm) diameter wire. Operates
at currents generally below 600 amps.
Outer flux cone gives full flux coverage
with minimum consumption.
Order K231-x
Contact Jaw Assembly
Single arc contact jaw assembly for
1/8-7/32" (3.2-5.6 mm) diameter wire.
Rugged contact jaws for maximum life
at currents over 600 amps.
Order K226R
Positive Contact Assembly
For single arc welding at high currents
(optional T12928 water cooling attach-
ment recommended when Innershield®
welding over 600 amps).
Order K148x
Linc-Fill® Long Stickout Extension
Linc-Fill long stickout extension for
K148A Single Arc Positive Contact
Nozzle Assembly. Required for long
stickout technique.
Order K149-x
Narrow Gap Deep Groove Nozzle
For single arc 3/32" (2.4 mm) diameter
wire welding on thick walled steel plate
with nearly parallel-sided, narrow gap
joint preparations.
Order K386
Concentric Flux Cone Assembly
For use with K148B, Positive Contact
Nozzle Assembly. Gives concentric flux
coverage around the electrode.
Order K285
Tandem Arc Framework
Provides mountings with desired posi-
tioning adjustments for two standard
Automatic Wire Feed Heads. Includes
insulation and hardware to permit direct
mounting to a high capacity TC-3
Carriage, or to the user's gantry or
fixture for either direction of travel.
Order K387
Tandem Reels
Two Wire Reel Mounting for TC-3.
Order K390
Large Wire Twinarc® Contact
Assemblies
Feeds two 5/64" (2.0 mm), 3/32" (2.4
mm) or 1/8" (3.2 mm) wires for sub-
merged arc welding on "Fast-Fill" joints
or hardfacing beads.
Order K225
Tiny Twinarc® Contact Assemblies
Feeds two electrodes for high speed
submerged arc welds. Includes contact
nozzle, wire guides, drive rolls and
guides, and a second wire reel and
mounting bracket.
Order K129-x
Tiny Twinarc Solid Wire Straightener
Straightens wire diameters .045 thru
3/32" (1.2 thru 2.4 mm). Particularly
valuable on longer electrical stickout
procedures.
Order K281
TC-3 Self-Propelled Travel Carriage
Carries head and controls in either direc-
tion on a beam. Operates manually or
automatically with the weld controls.
Requires 115V AC 50 or 60 hertz input
power.
Order K325S, F, HCS, HCF
Vertical Lift Adjuster
Provides 4" (102 mm) hand crank
adjustment of vertical head position. It
also includes up to 3-3/4" (95.2 mm) in-
and-out horizontal adjustment with
stops that can be preset for simple rep-
etition of the same adjustment.
Order K29
Horizontal Adjuster
Provides crank adjustment of head posi-
tion. Has 2" (51 mm) horizontal travel.
Order K96
Wire Reel Assembly for 50-60 lb. Coils
Accommodates 50 lb. (22.7 kg) or 60 lb.
(27.2 kg) coils of wire on automatic wire
feeders. The unit includes a wire reel
mounting spindle and braking system.
Order K299