Filter
Top Products
2
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Symbols
END215-2
The following show the symbols used for the tool. Be sure that you
understand their meaning before use.
..........Read instruction manual.
..........Withdraw the main plug.
..........Wear safety glasses.
..........Do not place hand or fingers close to the blade.
..........Only for EU countries
Do not dispose of electric equipment together with
household waste material!
In observance of European Directive 2002/96/EC on
waste electrical and electronic equipment and its
implementation in accordance with national law,
electric equipment that have reached the end of their
life must be collected separately and returned to an
environmentally compatible recycling facility.
Intended use
The tool is intended for cutting in wood.
Power supply
The tool should be connected only to a power supply of the same
voltage as indicated on the nameplate, and can only be operated
on single-phase AC supply. They are double-insulated in
accordance with European Standard and can, therefore, also be
used from sockets without earth wire.
SAFETY INSTRUCTIONS ENA001-2
WARNING: When using electric tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, electric shock and personal
injury. Read all these instructions before operating this
product and save these instructions.
For safe operations:
1. Keep work area clean.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose power tools to rain. Do not use power tools in
damp or wet locations. Keep work area well lit. Do not use
power tools where there is risk to cause fire or explosion.
3. Guard against electric shock.
Avoid body contact with earthed or grounded surfaces (e.g.
pipes, radiators, ranges, refrigerators).
4. Keep children away.
Do not let visitors touch the tool or extension cord.
All visitors should be kept away from work area.
5. Store idle tools.
When not in use, tools should be stored in a dry, high or locked
up place, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate for which it was
intended.
7. Use the right tool.
Do not force small tools or attachments to do the job of a heavy
duty tool. Do not use tools for purposes not intended; for
example, do not use circular saws to cut tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, they can be caught in
moving parts. Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear protecting hair
covering to contain long hair.
9. Use safety glasses and hearing protection.
Also use face or dust mask if the cutting operation is dusty.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust extraction
and collection facilities ensure these are connected and
properly used.
11. Do not abuse the cord.
Never carry the tool by the cord or yank it to disconnect it from
the socket. Keep the cord away from heat, oil and sharp edges.
12. Secure work.
Use clamps or a vice to hold the work. It is safer than using
your hand and it frees both hands to operate the tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubrication and changing
accessories. Inspect tool cord periodically and if damaged
have it repaired by an authorized service facility. Inspect
extension cords periodically and replace, if damaged. Keep
handles dry, clean and free from oil and grease.
Model LB1200F
Wheel size 305 mm
Max. cutting capacity 165 mm
No load speed
High 840 min
-1
(50 Hz)/1,040 min
-1
(60 Hz)
Low 420 min
-1
(50 Hz)/520 min
-1
(60 Hz)
Cutting speed
High
13.3 m/s (800 m/min) (50 Hz)/
16.7 m/s (1,000 m/min) (60 Hz)
Low
6.7 m/s (400 m/min) (50 Hz)/
8.3 m/s (500 m/min) (60 Hz)
Blade size Circumference 2,240 mm x Width 6 mm, 13 mm, 16 mm
Overall dimensions 615 mm x 775 mm x 1,600 mm
Table size 560 mm x 400 mm
Net weight 81.2 kg