Milwaukee 2411-059 Cordless Drill User Manual


  Open as PDF
of 20
 
16
ASSEMBLY
WARNING Rechargeonlywiththechar-
gerspeciedforthebattery.Forspeciccharg-
inginstructions,readtheoperator’smanual
suppliedwithyourchargerandbattery.
WARNING Alwaysremovebattery
packbeforechangingorremovingacces-
sories.Onlyuseaccessoriesspecifically
recommendedforthistool.Othersmaybe
hazardous.
OPERATION
WARNINGToreducetheriskofin-
jury,keephandsawayfromallmovingparts.
Alwayswearsafetygogglesorglasseswith
sideshields.
WARNING Alwaysremovebattery
packbeforechangingorremovingacces-
sories.Onlyuseaccessoriesspecifically
recommendedforthistool.Othersmaybe
hazardous.
Inserting/RemovingtheBattery
To removethe battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
FuelGauge
To determine the amount of charge left in the bat-
tery, pull the trigger. The Fuel Gauge will light up
for 2-3 seconds.
To signal the end of charge, 1 light on the fuel
gauge will ash for 2-3 seconds.
InstallingBits
Always remove the battery before inserting or
removing bits. Select the proper style and size bit
for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16” off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the
bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the coun-
terclockwise direction.
TorqueSpecicationsforCat.No.2410-059
Clutch
Setting in.lbs
Applications
1-5
6-10
11-15
16-21
5-15
16-22
23-35
36-80
Small screws in softwood.
Medium screws in softwood or small
screws in hardwood.
Large screws in softwoods. Medium
screws in hardwood or large screws in
hardwood with pilot hole.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem
with the chuck’s operation.
SelectingDrillorDriveAction
(Cat. No. 2410-059)
1. Tousethedrillingmode, rotate
the clutch adjusting ring until the
drill symbol
appears in line
with the arrow.
2. Tousethedrivingmoderotate
the clutch adjusting ring until the
desired clutch setting appears in
line with the arrow.
The adjustable clutch, when prop-
erly adjusted, will slip at a preset
torque to prevent driving the screw
too deep into different materials
and to prevent damage to the screw or tool.
SelectingHammer,DrillorDriveAction
(Cat. No. 2411-059)
1. Tousethehammer-drilling
mode,rotate the application
selector ring until the hammer
symbol
appears in line with
the arrow. Apply pressure to the
bit to engage the hammering
mechanism.
NOTE: The number selected on the clutch
adjusting ring has no effect on operation of the
drill in hammer mode.
NOTE: When using carbide bits, do not use wa-
ter to settle dust. Do not attempt to drill through
steel reinforcing rods. This will damage the
carbide bits.
2. Tousethedrillingonlymode,
rotate the application selector ring
until the drill symbol
appears
in line with the arrow.
NOTE: The number selected on
the clutch adjusting ring has no
effect on operation of the drill in
drilling mode.
3. Tousethedrivingscrewsmode
rotate the application selector ring
until the drive symbol
appears
in line with the arrow. Then rotate
the clutch adjusting ring until the
desired clutch setting appears in
line with the arrow.
The adjustable clutch, when properly adjusted,
will slip at a preset torque to prevent driving the
screw too deep into different materials and to
prevent damage to the screw or tool.
1
1
2
 previous next