Filter
Top Products
Page 4
GENERAL SAFETY RULES
■ When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of electric shock or injury.
SPECIFIC SAFETY RULES
■ Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring or its cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the
operator.
■■
■■
■ Wait for the cutter to stop before setting the tool down. An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
■ Keep handles dry, clean, and free from oil, and
grease. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based
products or any strong solvents to clean your tool.
Following this rule will reduce the risk of serious per-
sonal injury.
■ Keep blades clean. Periodically check blades and
exhaust port for chip build-up. Clean blades mini-
mize stalling and kickback. Following this rule will
reduce the risk of serious personal injury.
■■
■■
■ Do not abuse cord. Never carry the tool by the cord
or yank it to disconnect it from the receptacle. Keep
cord away from heat, oil, and sharp edges. Follow-
ing this rule will reduce the risk of electric shock or fire.
■■
■■
■ Make sure your extension cord is in good condi-
tion. When using an extension cord, be sure to use
one heavy enough to carry the current your prod-
uct will draw. A wire gage size (A.W.G.) of at least
14 is recommended for an extension cord 100 feet
or less in length. A cord exceeding 100 feet is not
recommended. If in doubt, use the next heavier gage.
The smaller the gage number, the heavier the cord.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
■■
■■
■ Inspect for and remove all nails from lumber be-
fore planing. Following this rule will reduce the risk of
serious personal injury.
■■
■■
■ Drugs, alcohol, medication. Do not operate tool
while under the influence of drugs, alcohol, or any
medication. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
■■
■■
■ Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also.
Additional Rules For Safe Operation
■■
■■
■ Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
■■
■■
■ Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
■■
■■
■ Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
■■
■■
■ Protect your hearing. Wear hearing protection dur-
ing extended periods of operation. Following this rule
will reduce the risk of serious personal injury.
■■
■■
■ Inspect tool cords periodically and, if damaged, have
repaired at your nearest Factory Service Center or
other Authorized Service Organization. Constantly
stay aware of cord location. Following this rule will
reduce the risk of electric shock or fire.
■■
■■
■ Keep hands away from blades and planing area. Do
not reach underneath work while blades are rotat-
ing. Do not attempt to remove material while blades
are rotating. Blades continue to rotate after releas-
ing of trigger. Following this rule will reduce the risk of
serious personal injury.
■■
■■
■ Check damaged parts. Before further use of the tool,
a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A
guard or other part that is damaged should be prop-
erly repaired or replaced by an authorized service
center. Following this rule will reduce the risk of shock,
fire, or serious injury.
Service
■■
■■
■ Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.