Schumacher SF 4020 Battery Charger User Manual


 
2
553
1. WARNING: Wear complete eye protection and clothing
protection, when working with lead-acid batteries.
2. Make sure someone is within range of your voice or close
enough to come to your aid when you work with or near a
lead-acid battery.
3. Have plenty of fresh water and soap nearby for use if battery
acid contacts skin, clothing, or eyes. If battery acid contacts
skin or clothing, wash immediately with soap and water.
4. Avoid touching your eyes while working with a battery. Acid
particles (corrosion) may get into your eyes! If acid enters
your eye, immediately flood eye with running cold water for
at least 10 minutes. Get medical attention immediately.
5. Remove all personal metal items such as rings, bracelets,
necklaces, and watches when working with a lead-acid
battery. A lead-acid battery can produce a short-circuit current
high enough to weld a ring (or the like) to metal, causing a
severe burn.
6. Take care not to drop a metal tool or other metal onto the
battery. Metal may cause sparking or short circuit the battery
or another electrical devise. Sparking may cause an
explosion.
7. Always operate battery charger in an open well ventilated
area.
8. NEVER smoke or allow a spark or flame in the vicinity of the
battery or engine. Batteries generate explosive gases!
PERSONAL PRECAUTIONS AND SAFETY
B.
GROUND AND AC POWER CORD CONNECTIONS
C.
GROUNDING
SCREW
FIGURE 1 GROUNDING METHODS
Never place charger directly above the battery being charged,
gases from battery could damage the charger.
Never allow battery acid to drip on the charger when reading
specific gravity of filling battery.
Never operate charger in a closed in area, or restrict ventila-
tion in any way.
Do not set battery on top of the charger.
CHARGER LOCATION PRECAUTIONS
E.
1. Make sure you have a 12 volt or a 6 volt lead-acid battery
and select battery charger switch accordingly.
2. Clean battery terminals. Take care to keep corrosion from
coming in contact with your eyes.
3. If required, add distilled water in each cell until battery acid
reaches levels specified by battery manufacturer. This helps
purge excessive gas from cells. Do not overfill. For a bat-
tery without cell caps, carefully follow manufacturer's re-
charging instructions.
4. Study all battery manufacturer's specific precautions, such
as removing or not removing cell caps while charging, and
recommended rates of charge.
5. Be sure area around battery is well ventilated while battery
is being charged. Gas can be forcefully blown away by us-
ing a piece of cardboard or other non-metallic material as a
fan.
6. If necessary to remove battery from vehicle to charge, al-
ways remove grounded terminal from battery first. Make sure
all accessories in the vehicle are off, so as not to cause an
arc.
7. A marine (boat) battery must be removed and charged on
shore. To charge it on board requires equipment specially
designed for marine use.
PREPARING TO CHARGE
D.
Charger should be grounded to reduce the risk of electric shock.
Charger is equipped with an electric cord having an equipment
grounding conductor and a grounding plug. The plug must be
plugged into an outlet that is properly installed and grounded in
accordance with all local codes and ordinances. This battery
charger is designed for use on a nominal 120 volt circuit and has
a grounded plug that looks like the plug illustrated in FIGURE 1
(A). This plug should be used in a grounded outlet. The plug
pins must fit the receptacle (outlet).
ADAPTER: A temporary adapter, as shown in FIGURE 1 (B) and
(C), may be used to connect the charger plug to a two pole re-
ceptacle (outlet), as shown in FIGURE 1 (B).
NOTE: The temporary adapter should be used only until a prop-
erly grounded outlet can be installed by a qualified electrician.
DANGER: Never alter the AC cord or plug provided. If it will not fit outlet, have a proper outlet installed by a qualified electrician. Improper connection can result
in a risk of an electrical shock. DANGER: Before using an adapter, as illustrated, be certain that the center screw of the outlet plate is grounded. The green-
colored rigid ear or lug extending from the adapter must be connected to a properly grounded outlet. Make certain it is grounded. If necessary, replace original
outlet cover plate screw with a longer screw that will secure adapter ear or lug to outlet cover plate and make ground connection to grounded outlet.
"Use of adapter plug not allowed in Canada"