Filter
Top Products
-16-
%1>B5/1
!"'%$%$(
#$&%!%#>1B1:@5B1
9-5:@1:-:/1<1>2;>910.EA:-A@4;>5F10
<1>?;::189-E>1?A8@5:95?<8-/5:3;2
5:@1>:-8C5>1?-:0/;9<;:1:@?C45/4
/;A80/-A?1?1>5;A?4-F->0 We recom -
mend that all tool service be performed by a
Skil Factory Service Center or Authorized Skil
Service Station. SERVICE MEN: Disconnect
tool and/or charger from power source before
servicing.
&&$%
1-81>@2;>.-@@1>E<-/7?@4-@->1:1->5:3
@415>1:0;28521 If you notice decreased
tool performance or significantly shorter
running time between charges then it is time
to replace the battery pack. Failure to do so
can cause the tool to operate improperly or
damage the charger.
! ' &&$% "!+
;:3@1>9.-@@1>E?@;>-31?4;A80.15:
@4105?/4->310?@-@1 Battery packs last
longer and re-charge better when they are
stored discharged. Remember to fully re-
charge battery packs before using after
prolonged storage.
&""'$&"!
Your Skil tool has been properly lubricated
and is ready for use.
"&"$%
The motor in your tool has been engineered
for many hours of dependable service. To
maintain peak efficiency of the motor, we
recommend it be examined every six months.
Only a genuine Skil replacement motor
specially designed for your tool should be
used.
81-:5:3
&;-B;50-//501:@?-8C-E?
05?/;::1/@@41@;;8-:0;>
/4->31>2>;9@41<;C1>?A<<8E.12;>1
/81-:5:3 The tool may be cleaned most
effectively with com pressed dry air. 8C-E?
C1->?-21@E3;3381?C41:/81-:5:3@;;8?
C5@4/;9<>1??10-5>
Ventilation openings and switch levers must
be kept clean and free of foreign matter. Do
not attempt to clean by inserting pointed
objects through opening.
1>@-5:/81-:5:3-31:@?
-:0 ?;8B1:@? 0-9-31
<8-?@5/<->@?Some of these are: gasoline,
car bon tetrachloride, chlorinated cleaning
solvents, ammonia and household detergents
that contain ammonia.
!
WARNING
-5:@1:-:/1
$
'!!!!'&%!"&%
Variable speed control must be used with
caution for driving nuts and bolts with socket
set attach ments. The technique is to start
slowly, increasing speed as the nut or bolt runs
down. Set the nut or bolt snugly by slowing the
drill to a stop. If this procedure is not followed,
the tool will have a tendency to torque or twist
in your hands when the nut or bolt seats.
"%)%
11< 4-:0? -C-E 2>;9
/A@@5:3->1--:04;81?-C
11< E;A> ?1/;:0 4-:0 ;: @41 ?501
4-:081;>9;@;>4;A?5:3 If both hands are
holding the drill, they cannot be cut by the
hole saw. Hold the drill firmly to prevent loss
of control. Unplug drill when removing core.
Hole saws are ideal for use with lock
installation kits for 2-1/8” deadbolts or
locksets with 15/16” or 1” latch hole in
wooden and composition doors.
!
WARNING
!
WARNING
!
CAUTION
SM 1619X04215 05-09:SM 1619X04215 05-09 5/21/09 3:09 PM Page 16