Filter
Top Products
10 ► CR27 User Manual
TOOL STICKERS & TAGS
Failuretousehydraulichoselabeledandcertified
asnon-conductivewhenusinghydraulictoolson
ornearelectriclinesmayresultindeathor
Forproperandsafeoperationreadownersmanual
andmwkesurethatyouhavebeenproperly
trainedincorrectproceduresrequiredforwork
seriousinjury.
onoraroundelectriclines.
ELECTROCUTION
HAZARD
DANGER
12412
Electrical Warning Decal
05153
Stanley Decal
15863
Danger Decal
27694
Danger Decal
DANGER
THIS SAW BLADE OF THE CR27 WILL CONTINUE TO ROTATE
FOR UP TO 15 SECONDS OR MORE AFTER RELEASING THE
ON/OFF TRIGGER. DURING THIS “COAST DOWN” TIME,
CONTACT WITH THE BLADE OF THE CR27 MAY RESULT IN
SEVERE PERSONAL INJURY.
AFTER RELEASING THE ON/OFF TRIGGER, SAW OPERATORS
MUST BE CERTAIN THAT THE BLADE HAS COME TO A COMPLETE
STOP BEFORE PLACING THE SAW ON THE GROUND, LOWERING
THE SAW INTO THE TRUCKS BUCKET, STORING THE SAW OR
CONTACTING THE BLADE IN ANY WAY. FAILURE TO OBSERVE
THESE PRECAUTIONS MAY RESULT IN SEVERE PERSONAL
INJURY.
OTHER WORKERS AND BYSTANDERS MUST STAY CLEAR OF
THE WORK AREA TO AVOID SEVERE PERSONAL INJURY RESULTING
FROM CONTACT WITH THE SAW BLADE AS WELL AS FALLING
LIMBS, BRANCHES AND OTHER DEBRIS.
SAFETY TAG P/N 15875 (Shown smaller then actual size)
DANGERDANGER
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CER-
TIFIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC
TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN
DEATH OR SERIOUS INJURY.
BEFORE USING HOSE LABELED AND CERTIFIED AS NON-
CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE
HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE
SHOULD BE REGULARLY TESTED FOR ELECTRIC CUR-
RENT LEAKAGE IN ACCORDANCE WITH YOUR SAFETY
DEPARTMENT INSTRUCTIONS.
2. A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJEC-
TION INTO THE BODY OR CAUSE OTHER SEVERE
PERSONAL INJURY.
A. DO NOT EXCEED SPECIFIED FLOW AND PRESSURE
FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY
CAUSE A LEAK OR BURST.
B. DO NOT EXCEED RATED WORKING PRESSURE OF
HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS
PRESSURE MAY CAUSE A LEAK OR BURST.
C. CHECK TOOL HOSE COUPLERS AND CONNECTORS
DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH
YOUR HANDS. CONTACT WITH A LEAK MAY RESULT
IN SEVERE PERSONAL INJURY.
IMPORTANT
D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO
NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR
DAMAGED HOSE.
3. MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-
NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.
SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-
NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE
MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT.
REVERSING CONNECTIONS MAY CAUSE REVERSE
TOOL OPERATION WHICH CAN RESULT IN SEVERE
PERSONAL INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-
CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN
LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY
THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.
5. BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.
KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-
TECTION.
7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE,
ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST
ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY
TRAINED PERSONNEL.
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie, OR 97062
Model
24827
Name Tag
03784
5-7 GPM Sticker