TOOL SPECIFICATIONS
All dimensions in inches unless otherwise specified.
-4-
651S5
Description 7/16” Crown Stapler
Operation Pressure Range
70-120 PSI (4.9 to 8.43kg/cm
2
)
Fastener Type 16S5 & 17S5 Series Staples
Fastener Gauge 16 & 17 Gauge
Fastener Range 1” to 2” (25mm to 50mm)
Magazine Capacity 120
Length 14”
Width 3 1/8”
Height 11”
Weight 4.3 lbs.
Tool Air Fitting:
This tool uses a free-flow connector plug, 1/4” N.P.T.The minimum inside diameter should be .200” (5mm).
The fitting must be capable of discharging tool air pressure when disconnected from the air supply.
Operating Pressure:
70 to 120 p.s.i.g. (4.9 to 8.43 kg/cm
2
). Select the operating pressure within in this range for best fastener
performance. DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
Air Consumption:
The 651 Series staplers require 5.3 cubic feet per minute or C.F.M. (150 liters per minute or LT/MIN) of free
air at 80PSI (5.6 kg/cm
2
) to operate at a rate of 100 fasteners per minute. To determine the appropriately
sized air compressor, take the actual rate at which the tool will be run and compare the required C.F.M.
(LT/MIN) to the compressors free air delivery (C.F.M./ LT/MIN) at 80 PSI (5.6 kg/cm
2
).
For example, if your fastener usage averages 50 fasteners per minute, you need 50% of the tools C.F.M.
required to operate the tool at the rate of 100 fasteners per minute. In this case, be sure that your air
compressor can deliver a minimum of 2.7 C.F.M. (75 LT/MIN) at 80 PSI(5.6 kg/cm
2
) for optimum performance.
FASTENER SPECIFICATIONS
Tool Model Fastener SKU Gauge Crown Width Length
651S5-1
16S5-35
16
7/16” 1-3/8” (35mm)
16S5-38
16
7/16” 1-1/2” (38mm)
16S5-44
16
7/16” 1-3/4” (44mm)
16S5-44GAL
16
7/16” 1-3/4” (44mm)
16S5-50
16
7/16” 2” (50mm)
16S5-50GAL
16
7/16” 2” (50mm)
17S5-25G
17
7/16” 1” (25mm)
17S5-28G
17
7/16” 1-1/8” (28mm)
17S5-31G 17 7/16” 1-1/4” (31mm)
17S5-34G 17 7/16” 1-3/8” (34mm)
17S5-38G 17 7/16” 1-1/2” (38mm)
17S5-41G 17 7/16” 1-5/8” (41mm)
17S5-44G 17 7/16” 1-3/4” (44mm)
17S5-50G 17 7/16” 2” (50mm)
* Stainless steel fasteners also available in certain sizes. Visit www.BOSTITCH.com for further details.
NOTE: BOSTITCH tools have been engineered to provide superior customer satisfaction and are
designed to achieve maximum performance when used with precision BOSTITCH fasteners engineered to
the same exacting standards. BOSTITCH cannot assume responsibility for product performance if
our tools are used with fasteners or accessories not meeting the specific requirements established
for genuine BOSTITCH fasteners and accessories.
MAINTAINING THE TOOL
W
hen working on air tools note the warnings in this manual and use extra care when
e
valuating problem tools.