Wagner SprayTech 524019 Paint Sprayer User Manual


  Open as PDF
of 24
 
10 Finish 230 AC Compact
GB
Spraying
5. Spraying
The AirCoat spray system has two dierent painting modes. The
AirCoat mode is used for ne nish work with low to medium
viscositymaterials(oil,stains,lacquers,etc...).Theairlessmodeis
usedforgeneralpaintingwithhighviscositymaterials(latex).
5.1 Spraying in AirCoat mode
Use the AirCoat mode for low-pressure ne nish work
(recommendedpumppressureupto69bar(6.9MPa,1000PSI).
1. Make sure that the airless spray hose is free of kinks and clear
of objects with sharp cutting edges.
2. Turn the pressure control knob counterclockwise to its lowest
setting.
3. Turnthecompressorairpressureregulator(b)
counterclockwise to its lowest setting.
4. Move the compressor ON/OFF switch to the ON position.
5. Move the pump ON/OFF switch to the ON position.
6. TurnthePRIME/SPRAYvalvetoSPRAY.
7. Turn the pressure control knob clockwise until the material
pressuregauge(a)reads27.5bar(2.7MPa,400PSI).Thepaint
hoseshouldstienaspaintbeginstoowthroughit.
8. Turntheairpressureregulator(b)clockwiseuntiltheair
pressuregauge(c)reads1.3bar(0.13MPa,20PSI).
(b)
(c)
(a)
9. Unlock the spray gun gun.
10. Trigger the spray gun to bleed air out of the material hose.
11. When material reaches the spray tip, spray a test area to check
the spray pattern.
12. Adjustthespraypatterntothedesiredsizeandatomization.
• Usethepressurecontrolknobtocontroltheowofpaintto
the gun.
• Usetheairpressureregulatortocontroltheamountof
atomizationairavailabletothegun.
• Usethepatternadjustmentknobontheguntonetune
the spray pattern.
i
Refer to the spray gun Owner’s Manual for
information on the operation of the gun.
5.2 Spraying in Airless Mode
Usetheairlessmodeforgeneralhigh-pressurespraying(pump
pressurefrom34.4bar(3.4MPa,500psi)to193bar(19.3MPa,2800
PSI).
1. Make sure that the airless spray hose is free of kinks and clear
of objects with sharp cutting edges.
2. Turnthepressurecontrolknob(d)counterclockwisetoits
lowest setting.
3. TurnthePRIME/SPRAYvalve(e)toSPRAY.
(e)
(d)
4. Move the pump ON/OFF switch to the ON position.
5. Make sure the compressor ON/OFF switch is in the OFF
position.
6. Turn the pressure control knob clockwise to its highest
setting.Thepainthoseshouldstienaspaintbeginstoow
through it.
7. Unlock the gun by turning the gun lock nut counter-clockwise
(whenlookingfromthebackofthegun)threefullturns.This
opens the material valve in the gun.
8. Trigger the spray gun to bleed air out of the material hose.
9. When material reaches the spray tip, spray a test area to check
the spray pattern.
10. Use the lowest pressure setting necessary to get a good spray
pattern.
a. If the pressure is set too high, the spray pattern will be too
light.
b. If the pressure is set too low, tailing will appear or the paint
willspatteroutin“gobs”ratherthaninanespray.
10a.
10b.
 previous next