Filter
Top Products
44
Boschtools.com
Toll Free: 877-BOSCH-99
Item # Diameter
Usable
Length
Overall
Length Quantity
HCBG01 1/8" 2" 3" 1
HCBG0105 1/8" 2" 3" 5
HCBG01B25 1/8" 2" 3" 25
HCBG02 5/32" 4" 6" 1
HCBG0205 5/32" 4" 6" 5
HCBG02B25 5/32" 4" 6" 25
HCBG03 3/16" 2" 3" 1
HCBG0305 3/16" 2" 3" 5
HCBG03B25 3/16" 2" 3" 25
HCBG04 3/16" 4" 6" 1
HCBG0405 3/16" 4" 6" 5
HCBG04B25 3/16" 4" 6" 25
HCBG05 7/32" 4" 6" 1
HCBG0505 7/32" 4" 6" 5
HCBG05B25 7/32" 4" 6" 25
HCBG06 1/4" 4" 6" 1
HCBG0605 1/4" 4" 6" 5
HCBG06B25 1/4" 4" 6" 25
HCBG07 1/4" 6" 8" 1
HCBG08 1/4" 10" 12" 1
HCBG09 5/16" 4" 6" 1
HCBG0905 5/16" 4" 6" 5
HCBG09B25 5/16" 4" 6" 25
HCBG10 5/16" 7-1/2" 10" 1
HCBG11 5/16" 10" 12" 1
HCBG12 3/8" 4" 6" 1
HCBG1205 3/8" 4" 6" 5
HCBG12B25 3/8" 4" 6" 25
HCBG13 3/8" 8" 10" 1
HCBG14 3/8" 10" 12" 1
HCBG15 7/16" 4" 6" 1
HCBG1505 7/16" 4" 6" 5
HCBG15B25 7/16" 4" 6" 25
HCBG16 1/2" 4" 6" 1
HCBG1605 1/2" 4" 6" 5
HCBG16B25 1/2" 4" 6" 25
HCBG17 1/2" 8" 10" 1
HCBG18 1/2" 10" 12" 1
HCBG19 9/16" 7-1/2" 10" 1
HCBG20 5/8" 4" 6" 1
HCBG2005 5/8" 4" 6" 5
HCBG20B25 5/8" 4" 6" 25
HCBG21 5/8" 10" 12" 1
HCBG22 3/4" 4" 6" 1
HCBG23 3/4" 10" 12" 1
HCBG24 7/8" 4" 6" 1
HCBG25 7/8" 10" 12" 1
HCBG26 1" 4" 6" 1
HCBG27 1" 10" 12" 1
Tapcon
®
is a registered trademark of Illinois Tool Works.
SDS-plus
®
is a registered trademark of Robert Bosch GmbH.
Allen
®
is a registered trademark of Industrial Fasteners Inc.
Phillips
®
is a registered trademark of Phillips Screw Co.
Hammer Drill Bits
SDS-plus®
Hammer Carbide
Blue Granite™ Carbide Hammer Drill Bits
Anchor Drive Installation Kit
SDS-plus® shank bits for use with Tapcon® / Condrive systems. Hex drive on bit
fits into driver sleeve.
• 1/4" hex shoulder for drive sleeve used to set masonry screws
Blue Granite™ Carbide Hammer Drill Bit Sets
Fast impact drilling in concrete, stone and masonry. Low voltage, high
temperature brazing prevents carbide cutting edge from breaking out even
when heat builds up during deep drilling. Various usable lengths up to 10".
• Milled u-flute and deep-cut spiral single-flute designs combined with
a diamond ground carbide tip to provide fast removal of drilling dust
• Perfect "on-center" diamond tip grinding for fast starts and drilling
• Inductive hardening process provides a softer shank for better
gripping power
Item # Description Sizes
HCBG500
5 pc. Industrial Hammer
Drill Bit Starter Set
1/8" x 2" x 3"; 3/16" x 4" x 6";
1/4" x 4" x 6"; 5/16" x 4" x 6";
and 3/8" x 4" x 6"
HCBG600T
6 pc. Industrial Hammer
Drill Bit Tapcon® Set
3 ea. of 5/32" x 4" x 6"
and 3/16" x 4" x 6"
HCBG700
7 pc. Industrial Hammer
Drill Bit Set
One 1/8" x 2" x 3", Two 5/32" x 3" x 6",
Two 3/16" x 4" x 6", One 1/4" x 4" x 6",
One 3/8 x 4" x 6"
HCBG800
8 pc. Industrial Hammer
Drill Bit Master Set
One 3/16" x 4" x 6", Two 1/4" x 4" x 6",
One 5/16" x 4" x 6", Two 3/8" x 4" x 6",
One 1/2" x 4" x 6", and One 5/8" x 4" x 6"
Item # Description
HC2309
9 pc. anchor drive installation kit—5/32" x 7" and 3/16" x 7"
Tapcon® hex bits, #2 & #3 Phillips® insert bits, bit holder, 5-3/4"
sleeve, 1/4" & 5/16" sockets and Allen® wrench
HCBG800
Masonry/Concrete Drilling