Cabela's 52-0601 Cordless Saw User Manual


  Open as PDF
of 6
 
-2-
COMPONENT LIST
DIAGRAM PART PART NO.
NUMBER DESCRIPTION NUMBER
1 CuttingBlade(2) 52-0301
2 SpinTesterAssembly(2) 52-0302
3 ShaftPositionBracket 52-0305
4 MeasuringTape 52-0316
5 SocketHeadCapScrew 52-0320
6 PowerCord N/A
7 On/OffSwitch N/A
8 DustCollector 52-0331
9 DustCollectorBracket 52-0332
10 ThumbScrew(2) 52-0333
11 Small(1-1/4”(3.2cm))DustCollectorAdaptor 52-0340
12 Large(2-1/4”(5.7cm))DustCollectorAdaptor 52-0341
13 ArrowShaftGuide 52-0306
14 ElectricMotor8000RPM 52-0202
15 RubberFeet 52-0329
16 WrenchKit 52-0330
17 BladeMountingBracketAssembly 52-0314
17aBladeSpacer
17bBladeRetainingNut
ARROW SAW BLADE REPLACEMENT
Your Arrow Saw comes complete with two, reinforced Cutting Blades.
These Cutting Blades are ideal for cutting both carbon and aluminum
arrow shafts. To order replacement Cutting Blades, contact Customer
Service at the telephone number listed on the back of this manual.
1. Set the On/Off Power Switch to the “OFF”
position. Disconnect the Power Cord from the
power source.
2. Loosen the two Thumb Screws holding the
Blade Shield to the Arrow Saw. Figure 13
3. Remove the Thumb Screws and Cutting
Blade Shield.
3. Remove the Socket Head Cap Screw
securing the Arrow Shaft Guide to the Base.
Figure 14
4. Remove the Arrow Shaft Guide.
5. Insert the long leg of the largest Allen
Wrench supplied with your Arrow Saw into
one of the holes in the outer edge of the Blade
Mounting Bracket. Figure 15
6. Place the Wrench onto the Blade Retaining
Nut. While holding the Allen Wrench, loosen
the Blade Retaining Nut (rotate counter
clockwise) until you can remove it by hand.
7. Remove the Blade Retaining Nut, Blade
Spacer and Cutting Blade.
8. Carefully install a new Cutting Blade.
CAUTION: NEVER USE A BROKEN, WORN
OR CRACKED BLADE!
9. Re-install the Blade Spacer and Blade
Retaining Nut.
10. Re-install the Arrow Shaft Guide and
Blade Shield. CAUTION: NEVER OPERATE
THE ARROW SAW WITHOUT THE BLADE
SHIELD SECURELY MOUNTED IN PLACE!
The Arrow Saw Cutting Blade rotates at very high speeds. It is normal for the Arrow
Saw to vibrate during operation. If you experience excessive noise and/or vibration
during operation, or blade breakage, check all parts to ensure they are properly and
securely mounted. If the problem continues, please contact Customer Service.
FIGURE 13
Blade Shield
Thumb Screws
Arrow Shaft
Guide
FIGURE 14
Arrow Shaft
Guide
Socket Head
Cap Screw
Base
Cutting
Blade
FIGURE 15
Allen
Wrench
Cutting
Blade
Base
Blade
Mounting
Bracket
Blade
Retaining
Nut
Blade
Spacer
Wrench
-11-
WARNING! Before cleaning, assembling or disassembling the Arrow
Saw, make sure it is turned OFF and the PLUG IS REMOVED FROM THE
OUTLET/POWER SOURCE!
Before beginning the assembly, check the package contents for all of the parts.
If you are missing any parts, or if any parts are damaged, contact
Cabela’s Customer Service- Retail Store Purchases 1-800-905-2731 (U.S. & Canada) /
Catalog & Internet Purchases: 1-800-237-8888 / All International: 1-308-234-5555
 previous next