Filter
Top Products
RULES FOR SAFE OPERATION (Continued)
m
N
NEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal spark4ngofthe motor could
igniteflammable liquids,gases, or fumes.
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-basedproductsor any
strong solventstoclean yourtool.
STAY ALERT. Watch what you are doing and
use common sense. Do not operate tool when
you are tired, Do not rush,
CHECK DAMAGED PARTS. Before further use
of the tool,a guard or other part that is damaged
should becarefully checked todetermine that it
willoperate properlyand perform its intended
function. Check for alignment ofmoving parts, •
bindingof movingparts, breakage of parts,
mounting,and any other conditionsthat may
affect itsoperation.A guard or other partthat is
damaged shouldbe properly repaired or M
replaced by an authorized servicecenter unless
indicatedelsewhere in thisinstructionmanual.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defectiveswitches
replaced byan authorizedservice center.
DRUGS, ALCOHOL, MEDICATION. Do not
operate toolwhile under the influenceof drugs,
alcohol, or any medication.
DO NOT PLACE BA'I'FERY TOOLS OR THEIR
BA't'rERIES NEAR FIRE OR HEAT. They may
explode.
DO NOT CHARGE BA'I'rERY TOOL IN A
DAMP OR WET LOCATION.
Your batterytool shouldbe chargedin a location
where the temperatureis more than 5O°F but
lessthan IOO°F.
Under extreme usage or temperature conditions,
batteryleakage may occur. If liquidcomes in
contactwith your skin,wash immediateSywith
soap andwater, then neutralize with lemon juice
or vinegar. If liquid gets in your eyes, flush them
with clean water for at least 10 minutes, then
seek immediate medical attention.
If carryingyour battery toolat your side, make
sure it is notrunningand your finger is notonthe
switch. Avoid accidental starting.
SECURE WORK before applyingpower. NEVER
hold workpieca inyour hand or acrossyour legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
DRIVING SCREWS INTO ELECTRICAL
WIRING IN WALLS, CEILINGS, OR OTHER
AREAS CAN CAUSE THE SCREWDRIVER BIT B
OR COLLET TO BECOME ELECTRICALLY
LIVE. Do nottouch metal partswhen driving
screws into a wall; grasponlythe insulated
handle(s) or plastic housingwhen using thistool.
Make sure hiddenelectrical wiring,water pipes, _1,
and mechanical hazards are notin the path of
the bit when drivi_j screws into a walt.
• INSPECT FOR and remove all nailsfrom lumber
before drivi_3screws.
IMPORTANT SAFETY RULES FOR BATTERY
TOOLS
Battery toolsdo not have tobe plugged intoan
elentr_caloutlet; therefore, theyare always in
operating condition.Be aware of possible
hazards when not usingyour batterytoolor
when changingaccessories,
• USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do not substituteany
other charger. Use of anothercharger could
cause batteriesto explodecausing possible
,, I_erious_i_,iury.
SAVE THESE INSTRUCTIONS. This manual
containsimportantsafety and operating
instructions for battery chargeritem number
9-11081.
Before usingbattery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and productusing battery
charger.
WARNING: To reduce riskof injury,charge only
nickel-cadmiumtype rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
Do not expose charger to rainor snow.
Use of an attachment notrecommended or sold
bythe batterycharger manufacturer may result
in a riskof fire,electric shock,or injuryto
persons.
To reduce riskof damage tocharger body and
cord, pull by charger body ratherthan cord when
disconnectingcharger.
Make sure cordis located sothat itwill not be
stepped on, trippedover, orotherwisesubjected
to damage or stress.