Filter
Top Products
RULES FOR SAFE OPERATION (Continued)
• NEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal sparking of the motor could
ignite flammable liquids, gases, or fumes.
KEEP HANDLES DRY, CLEAN, AND FREE
FRO• OIL AND GREASE. Always use a clean
cloth when cleaning, Never use brake fluids,
gasoline, petroleum-based products or any
strong solvents to clean your tool.
• STAY ALERT. Watch what you are doing and
use common sense. DO not operate tool when
you are tired. Do not rush.
n
m
m
CHECK DAMAGED PARTS. Before further use
of the tool. a guard or other part that is damaged
should be carefully checked to determine that it
will operate propecly and pedorm its intended
function, Check for alignment of moving pads. •
binding of moving parts, breakage of pads,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or •
replaced by an authorized service center unless
indicated elsewhere in this instruction manual
• DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
• DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs.
alcohol, or any medication.
DO NOT PLACE BATTERY TOOLS OR 1HEIR
BATTERIES NEAR RRE OR HEAT. They may
explode.
DO NOT CHARGE BATTERY TOOL IN A
DAMP OR WET LOCATION.
Your batten/tool should be charged in a location
where the temperature is more than 5O°F but
less than 100°F.
Under extreme usage or temperature conditions,
battery leakage may occur. It liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets in your eyes, flush them
with clean water for at least t0 minutes, then
seek immediate medical attention.
If carrying your battery tool at your side, make
sure it is not running and your finger is not on the
switch. Avoid accidental starting.
SECURE WORK before applying power. NEVER
hold workpiece in your hand or across your legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS.
OR OTHER AREAS CAN CAUSE THE BIT OR •
CHUCK TO BECOME ELECTRICALLY LIVE.
DO not touch metal parts when d tilling into a wall;
grasp only the insulated handle(s) or plastic
housing when using this tool, Make sure hidden
electrical wiring, water pipes, and mechanical _1.
hazards are not in the path of the bit when
dhlling into a wall.
m INSPECT FOR and remove all nails from lumber
before drilling.
IMPORTANT SAFETY RULES FOR BA'I-rERY
TOOLS
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible
hazards when not using your battery tool or
when changing accessories.
• USE ONLY THE CHARGER PROVIDED WITH
YOUR BA'i-FERY TOOL. DO not substitute any
other charger. Use of another charger could
cause batteries to explode causing possible
serious injury.
SAVE THESE INSTRUCTIONS. This manual
contains impodant safety and operating
instructions for battery charger item number
9-11070 (976790-001).
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger.
WARNING: To reduce risk of injury, charge only
nickeJ-cadmium type recha_geable batteries.
Other types of batteries may burst causing
personal injury and damage.
m
Do notexposechargerto rainorsnow.
Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to
persons.
To reduce risk of damage to charger body and
cord._oull by charger body rather than cord when
disconnecting charger.
Make sure cord is located so that itwill not be
stepped on, tnpped over, or otherwise subjected
to damage or stress.