Filter
Top Products
English
4
DW7080
LOCKNUTS
END PLATE
DW7082
DW7084
Press down lightly on the operating handle and pull out the lock down pin, as shown in
Figure 4. Gently release the downward pressure and allow the arm to rise to its full height.
Use the lock down pin when carrying the saw from one place to another. Always use the
carrying handle to transport the saw or the hand indentations shown in Figure 3.
Specifications
CAPACITY OF CUT
50° miter left and right
48° bevel left: 3° right
0° miter
Max. Height 3.5" (89 mm) Result Width 3.5" (89 mm)
Max. Width 6.1" (155 mm) Result Height 1.25" (32 mm)
45° miter
Max. Height 3.5" (89 mm) Result Width 2.4" (61 mm)
Max. Width 4.2" (107 mm) Result Height 1.25" (32 mm)
45° bevel
Max. Height 2.3" (58 mm) Result Width 3.5" (89 mm)
Max. Width 6.1" (155 mm) Result Height .75" (19 mm)
31.62° miter and 33.85° bevel
Max. Width 5.25" (133 mm) Result Height .9" (23 mm)
DRIVE
120 Volt Motor
2200 Watts 15 Amp Motor
5000 RPM Cut Helical Gears with Roller and Ball Bearings
Carbide Tooth Blade Automatic Electric Brake
Optional Accessories
The following accessories, designed for your saw, may be helpful. In some cases, other
locally obtained work supports, length stops, clamps, etc., may be more appropriate. Use
care in selecting and using accessories.
Extension, Work Support: DW7080
Used to support long overhanging workpieces, the work support is user assembled.
Your saw table is designed to accept two work supports; one on each side.
Adjustable Length Stop: DW7051
Requires the use of one work support (see drawing). It is used to make repetitive cuts
of the same length from 0 to 42" (107 cm).
Clamp: DW7082
Used for firmly clamping workpiece to the saw fence for precision cutting.
Dust Bag: DW7053 (Included with some models)
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the
sawdust produced (not shown).
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Laser Guide System: DW7187
Powered by the saw, the bright laser line delivers enhanced visibility in low and high
light locations. Easy to install.
Miter Saw LED Worklight System: DWS7085
Lighting used for greater visibility and cutting alignment during operation. Easy to
install.
Miter Saw Replacement Kerf Plate: DW7055
This durable plastic uncut plate limits blade tear out.
DW7187
DWS7085
SAW BLADES: ALWAYS USE 10" (254 mm) SAW BLADES WITH 5/8" (16 mm) ARBOR
HOLES. SPEED RATING MUST BE AT LEAST 5500 RPM. Never use a smaller diameter
blade. It will not be guarded properly. Use crosscut blades only! Do not use blades
designed for ripping, combination blades or blades with hook angles in excess of 7˚.
BLADE DESCRIPTIONS
APPLICATION DIAMETER TEETH
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose 10" (254 mm) 40
Fine Crosscuts 10" (254 mm) 60
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts 10" (254 mm) 80
Non-ferrous metals 10" (254 mm) 80
NOTE: For cutting non-ferrous metals, use only saw blades
with TCG teeth designed for this purpose.
ACCESSORIES
WARNING: Since accessories, other than those offered by DEWALT, have not been
tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only D
EWALT, recommended accessories should be used with
this product.