Filter
Top Products
Preparation before use
How to put in a battery
1. Pull and remove the main body case in the direction of
the arrow. (Fig.2)
CAUTION
Do not remove the upper cap.
Remove the main body case holding the main body.
1. Do not use a leaky battery.
2. Use only an alkaline battery (size AA).
With other batteries (rechargeable batteries, etc.), full
performance will not be delivered as the power is low
or the battery life is short.
3. Correctly put in an alkaline battery according to the (
and ( indications on the main body.
4. Use a battery that is within the recommended period
of use.
5. Immediately take out the battery when used up.
6. Dispose of used batteries according to your local laws
and regulations, etc.
Precautions on using a battery
The battery life will differ depending on the ambient
temperature.
[When this product is used for about 4 minutes
(2 minutes in each mode) once a day with a Hitachi
alkaline battery LR6 (EX-S)]
About 3 weeks at an ambient temperature of 25°C
About 2 weeks at an ambient temperature of 15°C
The battery life has run down if the indication lamp
does not flash/light even when the switch is turned ON.
Replace the alkaline battery with a new one.
2. Correctly put in a size AA alkaline battery according to
the indications on the main body. (Fig.3)
CAUTION
If the battery is put in incorrectly, the indication lamp
will not light/flash.
Size AA alkaline battery
3. Install the main body case.
Align the depressions in the main body case with the
projections on the main body, and securely install the
main body case as far as it will go. (Fig.4)
Projections Depressions
Before use
1. Modes
Mode Item(s) used together
I. Ion cleansing - Cotton swab
- Your regular toner
II. Heating care
- Your regular lip balm
2. Mode switching
Switch
(OFF)
Heating careIon cleansing
(Single press)
(Switch press
in mid-process)
(Double press)
(Switch press in mid-process or a lapse of 2 minutes)
(Lapse of 2 minutes)
In ion cleansing mode
Remove jewelry and contact lenses.
(Cause of skin trouble or poor physical
condition)
Persons who use embedded or wearable
medical electronic devices should never
use this product. (This product may cause
medical electronic devices to malfunction.)
Use the ion cleansing mode within 2 minutes once a day.
Do not use this product more than 2 minutes
continuously; otherwise it may cause lip trouble.
1. Wash away dirt from lips cleanly.
Remove lipstick, etc., with a cleansing agent.
2. Cut a commercially available cotton swab and set it to
the main body.
(1) Remove the lower cap. (Fig.5)
(2) Cut a commercially available cotton swab so that its
stem portion becomes 5 to 10mm. (Fig.6)
Stem portion
5 to 10mm
How to determine the cutting size
The locating hole is intended to determine the cotton
swab length.
A paper-made stem can be cut by the locating hole.
If the stem portion of the cotton swab is plastic, crease
it with the locating hole, and then cut it with scissors.
If you do not use the locating hole, cut the cotton swab
so that its stem portion becomes 5 to 10mm.
(1) Insert the cotton swab in the locating hole in the
lower cap, and push the stem portion into the
narrowed part of the hole. (Fig.7)
(2) Draw out the stem portion frontward, and it stops at
a position of about 7mm. Incise and cut the stem
within 3mm from the surface of the lower cap.
(Fig.8)
About 7mm Within 3mm
Maximum cutting position
(3) If the stem portion of the cotton swab is made of
paper, it can be cut off by folding it from side to side
as it is. (Fig.9)