Filter
Top Products
4 5
FUNCTIONAL DESCRIPTION
1. WARNING: Some dust created by
power sanding, sawing, grinding, drill-
ing, and other construction activities
contains chemicals known to cause
cancer, birth defects or other reproduc-
tive harm. Some examples of these
chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement
and other masonry
products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this
type of work. To reduce your exposure
to these chemicals: work in a well ven-
tilated area, and work with approved
safety equipment, such as those dust
masks that are specifi cally designed to
fi lter out microscopic particles.
2. Read, understand, and follow the
instructions packaged with the router
table and router lift. Do not plug in
Remote Power until Router Table Motor
is fully installed.
3. Only use the following recommended
router tables and router lifts with this
motor.
JessEm Mast-R-Lift #02101 with
required Shim Kit #02116
JessEm Mast-R-Lift #02102 with
required Shim Kit #02116
JessEm Mast-R-Lift Excel #02201 with
required Shim Kit #02116.
Using tables and lifts that are not spe-
cifi cally recommended may not prop-
erly secure the Router Table Motor with
Remote Power. An improperly secured
Motor increases the risk of injury or
product damage.
4. Do not place motor in a router base
or hold motor by hand during use.
Motor is designed only for use properly
secured in a recommended JessEm
router lift or router table. This motor is
not designed for use in a MILWAUKEE
router base. Do not use this motor un-
less it is securely installed into a recom-
mended JessEm router lift and router
table.
SPECIFIC SAFETY RULES
5. Always wear safety goggles and dust
mask. Use only in a well ventilated
area. Using personal safety devices and
in a safe environment reduce the risk for
injury.
6. Some woods contain preservatives
that can be toxic. Take extra care to
prevent inhalation and skin contact
when working with these materials. Re-
quest, and follow, any safety information
available from your material supplier.
7. Always make sure the workpiece is
free from nails, screws and other for-
eign objects. Keep the working edge
away from the clamping surface.
Cutting these objects can cause loss of
control of the workpiece and damage to
the bit.
8. Never place hands near cutting sur-
face.
9. Never use dull or damaged bits.
Sharp bits must be handled with
care. Damaged bits can break during
use. Dull bits require more force, which
could cause the bit to break. Damaged
bits can throw carbide pieces and burn
the workpiece.
10. After changing the bit or making any
adjustments, make sure the collet nut
and any other adjustment devices are
securely tightened. Loose adjustment
devices can unexpectedly shift, causing
loss of control. Loose rotating compo-
nents will be violently thrown. Watch for
vibration or wobbling that could indicate
an improperly installed bit.
11. Always keep the power supply cord
away from moving parts on the tool.
12. Never start the tool when the bit is in
contact with the material. The bit cut-
ting edge may grab the material causing
loss of control of the workpiece.
13. Never touch the bit during or imme-
diately after use. After use the bit may
be hot enough to burn bare skin.
14. To reduce the risk of injury, avoid
“climb cutting.” Climb cutting can
cause the workpiece to be thrown
violently out of your control. Even small
router bits can result in climb cutting.
Always feed the workpiece against the
cutter rotation.
3
4
1. Variable speed dial
2. Lock key
3. On/Off switch
4. Cord
5. Power box nameplate (on back)
6. Motor unit nameplate (on back)
7. Motor
8. Collet assembly
1
8
7
2
5
6
Amperes
Double Insulated
Symbology
Volts Alternating Current
No Load Revolutions
per Minute (RPM)
Do not expose to rain or
use in damp locations.
No Load
RPM
10,000 -22,000
Volts
AC
120
Specifi cations
Amps
15
Motor
Cat. No
.
5626-69
For use with:
JessEm Mast-R-Lift™ #02101 with
required Shim Kit #02116
JessEm Mast-R-Lift™ #02102 with
required Shim Kit #02116
JessEm Mast-R-Lift™ Excel #02201 with
required Shim Kit #02116
* Consists of 5626-69 motor and
23-37-0175 power box.
Cat. No. 5626-68 *