Filter
Top Products
Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005
Web support: www.omegawolf.com/powercraft
Model Number: PRT-150
09
Safety instructions
finger on the switch when carrying the machine or if you connect the
running machine to the socket, this may lead to accidents.
(d) Remove the adjusting tools or the spanners before switching on the
machine. A tool or a key which is located in a revolving part of the
machine may lead to injuries.
(e) Concentrate at all times. Ensure a safe stand and keep your balance at all
times. In this case you will be able to control the machine better in
unexpected situations.
(f) Wear suitable clothing. Do not wear any loose clothing or jewellery. Keep
your hair, clothing and gloves clear of any moving parts.
(g) If dust extraction or collection devices can be mounted, make sure that
they are connected properly and are used in the proper way. The use of
these pieces of equipment reduce hazards caused by dust.
4) Careful handling and use of electric tools
(a) Use the correct tool for the job at hand.
(b) Do not use an electric tool, if the switch is defective. An electric tool,
which cannot be switched on or off, is dangerous and has to be repaired.
(c) Remove the plug from the socket before setting down the machine,
changing accessories or putting the machine aside. This precautionary
measure prevents the unintentional start of the machine.
(d) Keep unused electric tools out of reach of children. Do not permit
persons to use the machine who are not familiar with it or who have not
read these instructions. Electric tools are dangerous, if they are used by
inexperienced persons.
(e) Maintain the machine with care. Please check whether the movable parts
are perfectly operational and do not jam, whether parts have broken or
have been damaged in such a way that the function of the machine is
impaired. Have damaged parts repaired prior to using the machine. Many
accidents are caused by electric tools which are poorly maintained.
(f) Keep all cutting tools sharp and clean.
(g) Use the electric tool, the accessories, the insert tools, etc according to
these instructions, and in the way described for this special type of
apparatus. In the process, take the working conditions and the work to
be carried out into consideration. Only use this belt sander for the
purpose for which it is intended.
(h) Use clamps or vice to hold work. It is safer then using your hands and
frees both hands to operate the tool.
Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005
Web support: www.omegawolf.com/powercraft
Model Number: PRT-150
16
Assembly
• Insert two coach bolt (M6X25) into the holes on the top of guide for
fence pressure pad (Fig. 6).
• Put the guide for fence pressure pad on the top of fence, and align
two holes with the two holes on the fence, then insert two bolts
(M6X25) into the holes, and secure in position with nuts (Fig. 7).
• Slide the two front fence, in order to have enough space for fence
pressure pad, then put fence pressure pad on the two bolts, and secure
it in position with washer and locking knob (Fig. 8 and Fig. 9).
Fit table pressure pad (3, Fig. 1) by doing the following:
• Loosen all the fittings on table pressure pad.
• Loosen two screws on guide for table pressure pad (8, Fig. 1 - page
4), and align two hole on guide for table pressure into the two holes
on the front side wall on the table, then insert two screws into the
holes, secure it in position with nut (Fig. 10).
• Insert two coach bolts (M6X25) into the hole on guide for table pressure
pad, and put table pressure pad on the two bolts, and secure it in
position with washer and locking knob (Fig. 11 and Fig. 12)
Fit the switch box (5, Fig. 1) by doing the following:
• Align two holes on switch box into the two holes on the front side
wall of table.
• Fit in position with two Phillips head screws inserted from the front
of table secured with two nuts (Fig. 13).
Mounting extensions
Fig.18