Filter
Top Products
o • _ • ee
motor spec faCahons and e ectrmcalrequmrements
Th_is machine is designed to use a 3450 RPM moto_ only
Do not use any motor that r._r_s faster' than 3450 RPM,
It is wired for operation on t10-t20 vo_ts, 60 Hz. _dter-
nating current. IT MUST NOT BE CONVERTED "TO
OPERATE ON 230 VOI.TS. EVEN THOUGH SOME OF
THE RECOMMENDED MOTORS ARE DUAL VOLTAGE,
THESE CRAFTSMAN MOTORS HAVE BEEN
FOUND TO BE ACCEPTABLE FOR USE ON
THIS TOOL.
11/2 3450 110-120 12!6
1/2 3450 110-!20 1218
3/4 3450 t10-120 !219
3/4 3450 110-120 t226
CAUTION: Do not use blower or washing machine motor_
or any motor with an automatic reset overload protector
as their use may be hazardous.
CONNECTING TO POWER SOURCE OUTLET
This machine must be grounded while ip use to protect
the operator from electric shock,
This _x_wer tool is equipped with a 3-conductor cord and
grounding type plug which has a grounding prong Jisted by
Underwriters' Laboratories Association. The ground
conductor has _ green jacket and is attached to the tooi
housing at one end and to the ground prong in the
attachment p)ug at the other end.
This p]u[_ requi:re_s a mating 3-conductor grounded type
outJ_t as s.how_l.
if the ot_t}et you are pla:n:ning to use for this power tool is
of the two pretty type DO NOT REMOVE OR ALTER
THE GROUNDING PRONG IN ANY MANNER. Use an
adat_)te_ as showr_ an(t a_ways connect the grounding !ug to
k r_c:twn g_ouf_{t.
It is recommende(J that you have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE prong out_et:.
An adapter as shown below is available for connecting plugs
to 2-prong _ec{:ptactes, The green grounding lug extending
from the adapter must be connected to a permanent ground
s_ch as to a properly grounded outlet box.
Plug power cord into a 110-120V properly grounded type
outlet protected by a 15.amp, time delay or CircuitSaw_r
fuse or circuit breaker.
If you are not sure that your outlet is propet!¥ g, ounded,
have it checked by a qualified electrician,
WARNING: DO NOT PERIMIT FINGERS TO TOUCH
THE TERMINALS OF PLUGS WHEN INSTALLING OR
REMOVING THE PLUG TO OR FROM THE OUTLET.
WARNING: IF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN _INCUR THE POTENTIAL HAZARD
OF ELECTRICAL SHOCK. PARTICULARLY WHEN USED
IN DAMP LOCATIONS IN PROXIMITY TO PLUMBING,
IF AN ELECTRICAL SHOCK OCCURS THERE ISTHE
POTENTIAL OF A SECONDARY HAZARD SUCH AS
YOU_R HANDS CONTACTING THE CUTTING BLADE.
If power cord is worn or cut, or damaged in any way, have
it replaced immediately.
PROPERLY __
GROUNDED
OUTLET.,_ i
J
@
3-PRONG
PLUG
GROUNDING
PRONG
NOTE: The adapter illustrated is for use only if you already
have a properW grounded 2-prong receptacle.
The use of any extension cord will ,cause some loss of
power. To keep this to a minimum and to prevent over-
heating and motor burn-out, use the table below to deter-
mitre the mirdmtjm wire size (A.W.G.) extension cord. Use
only 3 wire extension cords which have 3-prong grounding
type plugs and 3-pole receptacles which accept the too&
plug.
Extensior_ Cord Length Wire Size A,W.G,
Up to 1OO Ft. 14
!00 200 Ft, !2
200-400 Ft. 8
CHECK MOTOR ROTATION
WARNING: FOR YOUR OWN SAFETY, MAKE SURE
PLUG tS NOT CONNECTED TO POWER SOURCE OUT
LET WHEN CHA_%IGtNG MOTOR ROTATION.
The mote." must rotate COUNTERCLOCKWISE whet
viewed from the s_qaft enci _o which you wil! mount th_
pu!_ey, (See page 1'O). _tf it does not, change the dire_,:._ior
acco_-diqg to the ir;structions furnished with the motor.