Wagner SprayTech 3.23 Paint Sprayer User Manual


  Open as PDF
of 32
 
14 ProSpray 3.23
GB
Servicing Repairs at the unit
10. Servicing
10.1 General servicing
Servicing of the unit should be carried out once annually by the
WAGNERservice.
1. Check high-pressure hoses, device connecting line and
plug for damage.
2. Checktheinletvalve,outletvalveandlterforwear.
10.2 High-pressure hose
Inspect the high-pressure hose visually for any notches or
bulges,inparticularatthetransitioninthettings.Itmustbe
possible to turn the union nuts freely.
11. Repairs at the unit
Switch the unit OFF.
Before all repair work: Unplug the power plug
from the outlet.
11.1 Relief valve
1. Useadriftpunchof2mmtoremovethegroovedpin(Fig.
10,Item1)fromthereliefvalvehandle(2).
2. Removethereliefvalvehandle(2)andcambase(3).
3. Usingawrench,removethevalvehousing(4)fromthe
pumpmanifold(6).
4. Ensurethattheseal(5)isseatedcorrectly,thenscrewthe
newvalvehousing(4)completelyintothepumpmanifold
(6).Tightensecurelywithawrench.
5. Alignthecambase(3)withtheholeinthepumpmanifold
(6).Lubricatethecambasewithgreaseandslideonthe
cam base.
6. Bringtheholeinthevalveshaft(7)andinthereliefvalve
handle(2)intoalignment.
7. Insertthegroovedpin(1)tosecurethereliefvalvehandle
in position.
3
7
4
1
2
6
5
11.2 Inlet and outlet valve
1. Remove the four screws in the front cover and then
remove the front cover.
2. SwitchtheunitONandthenOFFsothatthepistonrodis
positioned in the lower stroke position.
Danger of crushing - do not reach with the
ngers or tool between the moving parts.
3. Unplugthepowerplugfromtheoutlet.
4. Remove the retaining clip from the connecting bend at the
suction hose and pull off the suction hose.
5. Screw off the return hose.
6. Swiveltheunit90°totherearinordertoworkmoreeasily
on the material feed pump.
7. Remove the pusher stem clip and slide the pusher stem
housing(7)fromtheinletvalvehousing(1).
8. Unscrewtheinletvalvehousing(Fig.11,Item1)fromthe
pump manifold.
9. Removethelowerseal(2),lowerballguide(3),inletvalve
ball(4),inletvalveseat(5)andO-ring(6).
10. Clean all the parts with the corresponding cleaning agent.
Checktheinletvalvehousing(1),inletvalveseat(5)
andinletvalveball(4)forwearandreplacethepartsif
necessary.Iftheworninletvalveseat(5)isunusedon
one side, install it the other way round.
4
5
6
1
2
3
7
11. Unscrewoutletvalvehousing(Fig.12,Item8)fromthe
piston(9)withadjustingwrench.
12. Removetheupperballcage(11),crushwasher(10),
outletvalveball(12),andoutletvalveseat(13).
13. Clean all the parts with the corresponding cleaning agent.
Checkoutletvalvehousing(8),outletvalveseat(13),
outletvalveball(12),crushwasher(10),andupperball
cage(11)forwearandreplacepartsifnecessary.Ifthe
wornoutletvalveseat(13)isunusedononeside,installit
the other way round.
14. Carry out installation in the reverse order. Lubricate O-ring
(Fig.11,Item6)withmachinegreaseandensureproper
seatingintheinletvalvehousing(Fig.11,Item1).
Uncontrolled Copy
 previous next