Filter
Top Products
#).-<A
“READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by BULLET (•) symbol listed
BELOW and other safety precautions, may result in serious personal injury.
• =<764A76-?7:381-+-)<)<15- Multiple workpieces
cannot be adequately clamped or braced and may bind
on the blade or shift during cutting.
• -+-:<)16<0-<14-;)?1;57=6<-,7:84)+-,76)
4
->-4.1:5?7:3;=:.)+-*-.7:-=;16/ A level and firm
work surface reduces the risk of the tile saw becoming
unstable.
• $01;<7741; 67<-9=188-,?1<08:7>1;176; .7:
)<<)+016/)6)=@141):A.-6+-Insure that the work piece
is supported by the fence before cutting.
• 767<=;-)67<0-:8-:;76););=*;<1<=<-.7:)<)*4-
-@<-6;1767:);),,1<176)4;=887:< Unstable support
for the workpiece can cause the blade to bind or the
workpiece to shift during the cutting operation pulling you
and the helper into the spinning wheel.
• $0-+=<7..81-+-5=;<67<*-2)55-,)/)16;<7:
8:-;;=:-,*A)6A7<0-:5-)6;)/)16;<<0-;816616/
<14-*4),- If confined, i.e. using length stops, it could get
wedged against the blade and thrown toward you.
• -<<0-*4),-:-)+0.=44;8--,*-.7:-+76<)+<16/<0-
?7:381-+- This will help avoid thrown workpieces.
• .<0-?7:381-+-7:*4),-*-+75-;2)55-,7:
*7//-,,7?6<=:6<14-;)?HI*A:-4-);16/
;?1<+0')1<.7:)4457>16/8):<;<7;<78)6,=684=/
<0-<14-;)?<0-6?7:3<7.:--<0-2)55-,5)<-:1)4
Continued sawing with jammed workpiece could cause
loss of control or damage to tile saw.
#75-,=;<+:-)<-,*A87?-:;)6,16/
;)?16//:16,16/,:14416/)6,7<0-:
+76;<:=+<176)+<1>1<1-;+76<)16;+0-51+)4;367?6<7
+)=;-+)6+-:*1:<0,-.-+<;7:7<0-::-8:7,=+<1>-0):5
#75--@)584-;7.<0-;-+0-51+)4;):-
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other
masonry products, and
• Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
• $0-:-):-),,1<176)4;).-<A16;<:=+<176;.7:8):<1+=4):
78-:)<176;7.<0-;)?16<0-78-:)<16/;-+<176"-),
<0-:-;<7.<0-5)6=)4.7:;).-78-:)<176
$
Use the tile saw in a well lit area and on a level surface,
clean and smooth enough to reduce the risk of trips and
falls. Use it where neither the operator nor the casual
observer is forced to stand in line with the blade.
To avoid the possibility of the appliance plug or receptacle
getting wet, position tile saw to one side of a wall mounted
receptacle to prevent water from dripping onto the
receptacle or plug. The user should arrange a “drip loop” in
the cord connecting the saw to a receptacle. The “drip loop”
is that part of the cord below the level of the receptacle, or
the connector if an extension cord is used, to prevent water
traveling along the cord and coming in contact with the
receptacle.
$7:-,=+-<0-:1;37.-4-+<:7+=<176
J$=684=/<0-+7:,1.<0-84=/7:
:-+-8<)+4-/-<;?-<1;+766-+<<0-.=;-7:+1:+=1<
*:-)3-:<0)<;=8841-;87?-:<7<0-<774$0-6=684=/
)6,-@)516-.7:8:-;-6+-7.?)<-:16<0-:-+-8<)+4-
WARNIN
G
!
DANGER
!
WARNING
!
H#&$##$"%$#I
TILESAW
POWER
SUPPLY
CORD
TILESAW
SUPPORT
DRIP
LOOP
SM_2610008271_12-09:tile saw 12/17/09 3:25 PM Page 4