Filter
Top Products
Para Asistencia Técnica, Llame al Teléfono 1-800-424-8936
Sirvase darnos la siguiente información:
- Número del modelo
- Código impreso
Dirija toda la correspondencia a:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
DG490500CK, DG490700CK
31 Sp
Notas
General Safety
Information (Cont’d.)
3. Wear proper apparel. Do not wear
loose clothing, neckties, rings,
bracelets, or other jewelry which
may get caught in moving parts.
Nonslip footwear is recommended.
Wear protective hair covering to
contain long hair.
4. Always use attachments designed for
use with this tool. Do not use
damaged or worn attachments.
5. Attachments must be securely
attached. Loose attachments can
cause serious injury.
6. Use steady, even pressure when
using tool. Do not force. Too much
pressure can cause the wheel to
crack, break, or overheat.
7. Keep all nuts, bolts and screws tight
and ensure equipment is in safe
working condition.
8. Do not put hands near or under
moving parts.
WORK AREA
Do not operate a power tool
in an explosive atmosphere,
such as in the presence of
flammable liquids, gases, or dust.
Power tools create sparks which may
ignite the fumes or dust.
Keep
work
area clean and well lighted. Cluttered
benches and dark areas invite accidents.
Keep
children away. All visitors should be
kept a safe distance from work area.
Distractions can cause you to lose
control.
Make
workshop kid proof with padlocks,
master switches, or by removing starter
keys.
ELECTRICAL SAFETY
Do not use in a dangerous
environment. Do not use
power tools in damp or wet
locations or expose them to
rain. Water entering a power tool will
increase the risk of electric shock.
Reduce
the risk
of unintentional starting. Make sure
switch is in OFF position before
plugging in.
Do not abuse cord.
• Never carry tool by its cord.
• Never pull the cord to disconnect
from receptacle. Pull plug at outlet
rather than pulling the cord.
1. Make sure cord is located so that it will
not be stepped on, tripped over, or
otherwise subjected to damage or
stress.
2. Do not use an extension cord unless
absolutely necessary. Use of
improper extension cord could result
in a risk of fire and electric
shock. If an extension cord must be
used, make sure:
• That the pins on plug of extension
cord are the same number, size and
shape as those of plug.
• That the extension cord is properly
wired and in good electrical
condition.
• If an extension cord is to be used
outdoors it must be marked with the
suffix “W-A” or “W” following the
cord type designation to indicate it is
acceptable for outdoor use. For
example – SJTW-A.
• Make sure your extension cord is in
good condition. When using an
extension cord, be sure to use one
heavy enough to carry the current
your product will draw. An
undersized cord will cause a drop in
line voltage, resulting in loss of
power and overheating. The Table
titled “Minimum Wire Size (AWG) of
Extension Cord for Bench Grinder”
shows the correct size to use
depending on cord length and
nameplate ampere rating. If in
doubt, use the next heavier gauge.
The smaller the gauge number, the
heavier the cord.
GROUNDING INSTRUCTIONS
In the event of a malfunction or
breakdown, grounding provides a path
of least resistance for electric current to
reduce the risk of electric shock. This
tool is equipped with an electric cord
having an equipment-grounding
conductor and a grounding plug. The
plug must be plugged into a matching
outlet that is properly installed and
grounded in accordance with all local
codes and ordinances.
DO NOT modify the plug provided - if it
will not fit the outlet, have the proper
outlet installed by a qualified
electrician. Improper connection of the
equipment-grounding conductor can
result in a risk of electric shock. The
conductor with insulation having an
outer surface that is green with or
without yellow stripes is the
equipment-grounding conductor. If
repair or replacement of the electric
cord or plug is necessary, do not
connect the equipment-grounding
conductor to a live terminal.
Check with a qualified electrician or
service personnel if the grounding
instructions are not completely
understood or if in doubt as to
whether the tool is properly grounded.
Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-
pole receptacles that accept the tool’s
plug. Repair or replace damaged or
worn cord immediately.
This tool is intended for use on a circuit
that has an outlet that looks like the
one illustrated in Figure 1. The tool has
a grounding plug that looks like the
plug illustrated in Figure 1.
A temporary adapter, which looks like
the adapter illustrated in Figure 2, may
be used to connect the plug to a 2-pole
receptacle as shown if a properly
grounded outlet is not available. The
temporary adapter should be used only
until a properly grounded outlet can be
installed by a qualified electrician. The
green-colored rigid ear, lug, and the
like, extending from the adapter must
be connected to a permanent ground
such as a properly grounded outlet
box.
2
www.chpower.com
Operating Instructions
Figure 1
Length of Cord in Feet 25 50 100 150
AWG Size of Cord 18 16 16 14
Minimum Wire Size (AWG) of Extension Cord for Bench Grinder
Figure 2
Grounding means
Grounded outlet box cover
Metal
screw