Filter
Top Products
90°(0°) Stop
1. Disconnectthesawfromthepowersource.
2. Turnthebladeelevationhandwheelandraisethe
bladetothemaximumelevation.
3. Loosenthebladebevellockknob(1)andmovethe
bladetothemaximumverticalposition,thentighten
thelockknob(1).
4. Placeacombinationsquareonthetableandagainst
theblade(2)todetermineif thebladeis90° (0°)to
thetable.(Fig.P)
5. tfthebladeisnot90°(0°)tothetable,loosenthetwo
setscrews(4),locatedonthecollar(5)underneath
thetablesaw(Fig.Q)withthehexkey(Carton
ContentsJ)andbackoffthecollar.
6. Loosenthebevellockknob,turnthebladetilting
handwheelto movethebladeuntilitis90° (0°)tothe
tableandtightenthebevellockknob.
7. Adjustthecollar(5)soitcontactsthebracket(3)
whenthebladeis90° (0°)tothetable.Tightenthe
twosetscrews(4)(Fig.Q).
Fig.O
Fig.P
900(00) 450
45° Stop
1. Withthebladeintheupright90° (0°)position,loosen
thebevellockknobandmovethebladetothe
maximumbevelangle.
2. Placethecombinationsquareonthetableasshown
inFig.Ptocheckif thebladeis45° tothetable.
3. tfthebladeisnot45°tothetable,loosenthetwoset
screws(4),locatedonthecollar(5)underneaththe
tablesaw,(Fig.Q)withthehexkey(CartonContents
J),andbackoffthecollar.
15
4. Loosenthebladebevellockknob,turntheblade
tiltinghandwheeltomovethebladeuntilit is45° to
thetableandtightenthebladebevellockknob.
5.Adjustthecollar(5)soitcontactsthebracket(3)
whenthebladeis45° tothetable.Tightenthetwo
setscrews.
BLADETiLTiNGPOINTER
1. Whenthebladeispositionedat90°(0°),adjustthe
bladetiltpointerto read0° onthescale.
2. Loosenthemountingscrew,positionpointerover0°
andtightenthescrew.
NOTE:Makeatrialcutonscrapwoodbeforemaking
criticalcuts.Measureforexactness.
Fig.Q
4
450
90o
3
BLADEPARALLELTOTHEMITERGAUGEGROOVE
(FIG.R,S)
IA WARNING!
This adjustment was made at the factory, but it
should be rechecked and adjusted if necessary.
],A WARNING]
To prevent personal injury:
= Always disconnect plug from the power source
when making any adjustments.
• This adjustment must be correct or accurate cuts
can not be made. Also inaccurate adjustment can
result in kickback and serious personal injury.
1. Remove the safety switch key and unplug the saw.
2. Remove the blade guard for this procedure but
reinstall and realign after adjustment.
3. Raise the blade to the highest position and set at the
0° angle (90 ° straight up).
4. Select and mark, with a felt tip maker, a blade tooth
having a "right set" and rotate the blade so the
marked tooth is Y2in. above the table.
5. Place the combination square base (1) into the right
side miter gauge groove (2). (Fig. R)
6. Adjust the rule so it touches the front marked tooth
and lock ruler so it holds its position in the square
assembly.