Filter
Top Products
passes rather than attempting to make it with one pass.
Maximum dado width on this saw is 13/16" (20mm). DO
NOT USE WIDER COMBINATIONS.
CAUTION: Always check dado blade clearance before
plugging in the saw.
Be sure to place the guard and standard throat plate back in
position and check adjustments when the dado cuts are
complete.
Dust Collection
Your table saw is equipped with a dust shroud and dust col-
lection port. For best results, connect a vacuum to the port
at the rear of the saw.
If the saw is operated without a vacuum attached, most of
the dust will be blown out the dust collection port. However,
some dust will fall inside the base. If the saw is used on a
table or other surface without an opening on the bottom,
clean out the base and accumulated saw dust after each
cut.
After extended use, the saw’s dust collection system may
become clogged. To clear the dust collection system:
a) Unplug the saw.
b) Turn the saw on its side, so the bottom, open part of the
unit is accessible.
c) Open the dust access door shown in Figure 24 by
removing the two hair pin cotters shown. Clean out the
excess dust, and re-secure the access door with the hair
pin cotters.
When cutting wet wood without a vacuum or when cutting
with a dado blade, removing the dust access door may be
helpful in preventing clogs.
Lubrication
1. All motor bearings are permanently lubricated at the fac-
tory and no additional lubrication is needed.
2. The height adjustment screw may require periodic
cleaning and lubrication. If you have difficulty raising or
lowering the blade:
a) Unplug the saw.
b) Turn the saw on its side, so the bottom, open part of
the unit is accessible.
c) Clean and lubricate the height adjustment screws
threads on the underside of your saw with general
purpose grease, shown in Figure 25.
Accessories
Recommended accessories for use with your tool are avail-
able at extra cost from your distributor or local service center.
D
EWALT manufactures the following accessories for your
saw:
Portable Saw Stand
Outfeed Side Support
Replacement Throat Plate
Dado Throat Plate
CAUTION: The use of any non-recommended accesso-
ry may be hazardous.
If you need assistance in locating any accessory, please
contact D
EWALT Industrial Tool Co., 701 East Joppa Road,
Baltimore, MD 21286 or call 1-800-4-D
EWALT (1-800-433-
9258).
Cleaning
Use only mild soap and damp cloth to clean the tool. Never let
any liquid get inside the tool; never immerse any part of the tool
into a liquid. Never use solvents to clean saw or guard
components.
Important
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (including brush inspection
and replacement) should be performed by authorized ser-
vice centers or other qualified service organizations, always
using identical replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of war-
ranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
EWALT (1-800-433-
9258). This warranty does not apply to accessories or dam-
age caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you
may have other rights which vary in certain states or
provinces.
In addition to the warranty, D
EWALT tools are covered by
our:
1 YEAR FREE SERVICE
D
EWALT will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first year
after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your DEWALT Power Tool, Laser, or Nailer for any reason,
you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-D
EWALT
for a free replacement.
9
English