Filter
Top Products
UUSSIINNGG TTHHEE QQUUIICCKK LLOOCCKK LLEEVVEERR
The work vise is equipped with a threaded screw
clamp and handle for tightening the vise. The clamp is
also equipped with a quick lock release mechanism as
standard equipment. The clamp can be tightened
against the workpiece in the vise by turning the han-
dle clockwise and loosened by turning the handle
counterclockwise. To use the quick lock release
mechanism, follow the steps below. See Figure 8.
1. Release the tension on the screw clamp by turning
the handle counterclockwise for 1/2 to 1 full turn.
2. Lift the quick lock lever up and pull back the
screw clamp handle sliding the vise open.
3. To tighten, lift the quick lock lever
up and push the screw clamp for-
ward against the workpiece.
4. Push the quick lock lever down into
release mechanism.
5. Turn the screw clamp clockwise to
securely tighten the workpiece in the vise.
AATTTTAACCHHIINNGG TTHHEE VVIICCEE HHAANNDDLLEE
AATTTTAACCHHIINNGG TTHHEE RREEAARR SSPPAARRKK SSHHIIEELLDD
1. Place the spring washer over the hex
bolt followed by the flat washer and
then fit the hex bolt through the spark
deflector. Place the spark shield in the
correct position and tighten the hex
bolt.
2. Tighten the hex bolt to secure the
spark shield in position
OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS FFOORR TTHHEE CCUUTT--OOFFFF SSAAWW
DDoo nnoott uussee tthhee CCuutt--ooffff ssaaww iiff tthhee ppoowweerr ccoorrdd ((oorr eexxtteenn--
ssiioonn ccoorrdd,, iiff uusseedd)) iiss wwoorrnn,, ccuutt,, oorr ddaammaaggeedd
iinn aannyy ootthheerr wwaayy.. AA wwoorrnn oorr ddaamm--
aaggeedd ppoowweerr ccoorrdd mmuusstt bbee rreeppllaacceedd iimmmmeeddiiaatteellyy.. CCoonnttaacctt AAllllttrraaddee CCuusst
toommeerr
SSeerrvviiccee ttoo oobbttaaiinn tthhee pprrooppeerr rreeppllaacceemmeenntt ppoowweerr ccoorrdd.. FFaaiilluurree ttoo aaddhheerree ttoo
tthhiiss wwaarrnniinngg ccoouulldd rre
essuulltt iinn ddaammaaggee ttoo tthhee CCuutt--ooffff ssaaww mmoottoorr,, ffiirree,, oorr sseevveerree
eelleeccttrriiccaall sshhoocckk oorr eevveenn ddeeaatthh ttoo tthhee ooppeerra
attoorr..
SSEECCUURRIINNGG TTHHEE TTRRIIGGGGEERR SSWWIITTCCHH
The 14" Cut-off saw should always be protected
against unauthorized usage. Follow the steps
below to secure the Cut-off saw when not in
use.
17
FIGURE 11. SECURING THE
TRIGGER SWITCH
18
FIGURE 8. USING THE
QUICK LOCK LEVER
FIGURE 9. ATTACHING
THE VISE HANDLE
FIGURE 10. ATTACHING
THE REAR SPARK SHEILD
1. Fit the vice handle onto the end
of the vice.
2. Fit the spring washer over the
hex screw followed by the flat
washer.
3. Place the hex screw inside the
vice handle and secure the vice
handle to the vice by tightening
the hex screw in a clockwise
direction.
4. Fit the cap onto the vice handle.