Filter
Top Products
AACCCCEESSSSOORRIIEESS
UUssee oonnllyy aacccceessssoorriieess tthhaatt aarree rreeccoommmmeennddeedd bbyy tthhee mmaannuuffaaccttuurreerr ffoorr yyoouurr mmooddeell..
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
AAllwwaayyss a
attttaacchh ggrroouunnddeedd ((33--pprroonngg)) eexxtteennssiioonn ccoorrddss ttoo ggrroouunnddeedd ((33--hhoollee)) oouuttlleettss..
IIff yyoouu mmuusstt uussee aann eexxtteennssiioonn
ccoorrdd,, bbee ssuurree tthhaatt tthhee ggaauuggee iiss llaarrggee eennoouugghh ttoo ccaarrrryy
tthhee aammoouunntt ooff ccuurrrreenntt nneecceessssaarryy ffoorr yyoouurr ppoowweer
r ttooooll..
If not, your tool may
experience a loss of power, excessive voltage drop or overheating. The smaller the
gauge number, the heavier the cord (see table below).
RREECCOOMMMMEENNDDEEDD SSIIZZEESS OOFF EEXXTTEENNSSIIOONN CCOORRDDSS 112200 VVOOLLTT AACC 6600 HHZZ TTOOOOLLSS
TTOOOOLL CCUURRRREENNTT RRAATTIINNGG CCOONNDDUUCCTTOORR SSIIZZEE IINN AA..WW..GG
AMPERE 10FT. 25FT. 50FT. 100FT.
3-6 18 18 18 18
6-8 18 18 18 16
8-10 18 18 18 14
10-12 16 16 14 14
12-16 14 12 12 -
16-20 12 12 12 -
SSPPEECCIIFFIICCAATTIIOONNSS
SSPPEECCIIFFIICCAATTIIOONNSS
Voltage 19.2V
Light Bulb Type Krypton 19.2V 0.6 A
Charger Input 120V 60Hz
Charging Time Approx. 3 Hours
Battery Type Ni-Cad
PPRROOTTEECCTTIINNGG TTHHEE EENNVVIIRROONNMMEENNTT
BBAATTTTEERRIIEESS
Alltrade batteries can be recharged many times. At the end of their useful life, recy-
cle batteries with due care for our environment.
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call
11--880000--882222--88883377
. Collected batteries will be recycled or disposed of properly.
1. Remove the battery pack from the
Worklight.
2. Hold the top of the Worklight with
one hand while twisting the rim in a
counter-clockwise direction with the
other. Continue turning until the rim
comes loose.
3. Remove the bulb by turning it slightly
and pulling it out of the bulb fitting.
Be careful not to damage the delicate
parts inside the case.
4. Insert the new bulb, then carefully
put the rim back in place and turn
it clockwise to tighten it.
MMAAIINNTTEENNAANNCCEE AANNDD CCLLEEAANNIINNGG
AAllwwaayyss rreemmoovvee tthhee bbaatttteerryy ppaacckk bbeeffoorree aatttteemmppttiinngg
cclleeaanniinngg oorr mmaaiinntteennaannccee..
UU
ssee oonnllyy mmiilldd ssooaapp aanndd aa ddaammpp ccllootthh ttoo cclleeaann tthhee ttooooll..
Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
AAllwwaayyss cclleeaann tthhee bbaatttteerryy ppaacckk uussiinngg oonnllyy aa ddr
ryy ccllootthh.. DDoo nnoott uussee lliiqquuiiddss..
AAllwwaayyss uunnpplluugg tthhee cchhaarrggeerr bbeeffoorree cclleeaanniinngg iitt..
RReegguullaarrllyy cclleeaann tthhee vveennt
tiillaattiioonn sslloottss iinn yyoouurr ttooooll aanndd cchhaarrggeerr uussiinngg oonnllyy aa ssoofftt
bbrruusshh oorr ddrryy ccllootthh..
NNeevveerr ooppeenn tthhee WWoorrkklliiggh
htt ccaassee,, bbaatttteerryy ppaacckk oorr cchhaarrggeerr..
Do not attempt to repair
the Worklight, battery pack or charger yourself. Opening any of these parts will void
your warranty.
UUssee oonnllyy aauutthhoorriizzeedd rreeppllaacceemmeenntt ppaarrttss ffoorr yyoouurr ttooooll..
Equipment service must be performed only by qualified repair personnel using
authorized replacement parts. Service or maintenance by unqualified personnel
could result in considerable risk of personal injury. Use of unauthorized parts or
failure to follow maintenance instructions may create a risk of electric shock or
injury.
11 12
REPLACEMENT
BULB