Filter
Top Products
SSYYMMBBOOLL NNAAMMEE EEXXPPLLAANNAATTIIOONN
Diameter Size of Drill Bits,
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
FFUUNNCCTTIIOONNAALL DDEESSCCRRIIPPTTIIOONN
BBee aawwaarree tthhaatt tthhiiss ttooooll iiss aallwwaayyss iinn aann ooppeerraattiinngg ccoonnddiittiioonn
bbeeccaauussee iitt ddooeess n
noott hhaavvee ttoo bbee pplluuggggeedd iinnttoo aann eelleeccttrriiccaall oouuttlleett..
Always turn
the switch
““OOFFFF””
and remove the battery pack before changing bits.
CCOONNTTRROOLLSS AANNDD CCOOMMPPOONNEENNTTSS::
1. Battery Pack
2. Release Buttons
on Each Side
3. 120V AC Adapter
4. Charger
5. LED Charging Indicators
6. Saw Shoe
7. Trigger Switch
9
WWhheenn bbllaaddee iiss bbiinnddiinngg,, oorr wwhheenn iinntteerrrruuppttiinngg aa ccuutt ffoorr aannyy rreeaassoonn,, rreelleeaassee tthhee
ttrriiggggeerr aanndd hhoolldd tthhee s
saaww mmoottiioonnlleessss iinn tthhee mmaatteerriiaall uunnttiill tthhee bbllaaddee ccoommeess ttoo
aa ccoommpplleettee ssttoopp.. NNeevveerr aatttteemmpptt ttoo rreemmoovvee tthhee
ssaaww ffrroomm tthhee wwoorrkk oorr ppuullll tthhee
ssaaww bbaacckkwwaarrdd wwhhiillee tthhee bbllaaddee iiss iinn mmoottiioonn oorr KKIICCKKBBAACCKK mmaayy ooccccuurr..
Investigate and take corrective actions to eliminate the cause of blade binding.
WWhheen
n rreessttaarrttiinngg aa ssaaww iinn tthhee wwoorrkk ppiieeccee,, cceenntteerr tthhee ssaaww bbllaaddee iinn tthhee kkeerrff aanndd
cchheecckk tthhaatt tteeeetthh aarree nnoott e
ennggaaggeedd iinnttoo tthhee mmaatteerriiaall..
If saw blade is binding, it
may walk up or KICKBACK from the work piece as the saw is restarted.
SSuuppppoorrtt llaarrggee ppaanneellss ttoo mmiinniimmiizzee tthhee rriisskk ooff bbllaaddee ppiinncchhiinngg aanndd KKIICCKKBBAAC
CKK..
Large
panels tend to sag under their own weight. Supports must be placed under the panel
on both sides, near the line of cut and near the edge of the panel.
DDoo nnoott uussee dduullll oorr ddaammaaggeedd bbllaaddee..
Unsharpened or improperly set blades pro-
duce narrow kerf causing excessive friction, blade binding and KICKBACK.
BBllaaddee ddeepptthh aanndd bbeevveell aaddjjuussttiinngg lloocckkiinngg lleevveerrss mmuusstt bbee ttiig
ghhtt aanndd sseeccuurree
bbeeffoorree mmaakkiinngg ccuutt..
If blade adjustment shifts while cutting, it will cause bind-
ing and KICKBACK.
UUssee eexxttrraa ccaauuttiioonn wwhheenn mmaakkiinngg aa ““PPoocckkeett CCuutt”” iinnttoo eexxiissttiinngg wwaallllss
oorr ootthheerr
bblliinndd aarreeaass..
The protruding blade may cut objects that can cause KICKBACK.
SSYYMMBBOOLLSS
IIMMPPOORRTTAANNTT::
Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SSYYMMBBOOLL NNAAMMEE EEXXPPLLAANNAATTIIOONN
V Volts Voltage (Potential)
A Amperes Current
Hz Hertz Frequency (Cycles per Second)
W Watt Power
Kg Kilograms Weight
Alternating Current Type of Current
Direct Current Type of Current
Alternating or Direct Current Type of Current
Earthing Terminal Grounding Terminal
Class II Construction Denotes Double Insulation
min Minutes Time
s Seconds Time
8. Lock-Off Button
9. Rubber Grip
AACCCCEESSSSOORRIIEESS::
10. Saw Blades (2)
11. Rip Fence Guide
CCOOMMPPOONNEENNTT MMOODDEELL NNUUMMBBEERR
BATTERY PACK 690071
CHARGER 690507
SAW BLADES 690086
1
2
3
10
11
6
7
8
9
4
5