Filter
Top Products
**&) *
# %*+##&'+ &%***&) *
"&,).#*+)#0)+) #)
For in plant and yard towing. Comes standard with a Duo-Hitch™, a
2” Ball and Lunette Eye combination Hitch.
"+) #)Two-wheeled trailer with optional fender and
light package. For highway use, consult applicable federal, state,
and local laws regarding possible additional requirements. Comes
standard with a Duo-Hitch™, a 2” Ball and Lunette Eye combination
hitch. &D67D
"+D3;>7D
"7@67D#;9:F";F
"34>7*FAD397)35=
"*')"))*+&)Easily mounts to standard muffler.
"**&)0*+ - Includes 35 ft. (10m) of electrode cable
and 30 ft. (9.1m) of work cable, headshield, work clamp electrode
holder. Cables are rated at 400 amps, 100% duty cycle.
" 25 ft (7.6m) or "100 ft. (30.4m) )$&+&%+)&#
Portable control provides same dial range as the output control on
the welder. Has a convenient 6 pin plug for easy connection to the
welder.
"Digital weld meters kit with easy to read digital meters for
volts and amps. Easy to install.
"%'&.)'#," +
Provides four 120 volt plugs rated at 20 amps each and one dual
voltage, full KVA plug rated at 120/240 volts, 50 amps.
")'&.)'#," +
Provides four 120 volt plugs rated at 15 amps each and one dual
voltage, full KVA plug rated at 120/240 volts, 50 amps.
+$'-'&.)'#,':3E7
+$'-'&.)'#,':3E7
",##"-'+)" +
Plugs into the 120/240V NEMA 14-50R receptacle on the case front
(which accepts 4-prong plugs) and converts it to a NEMA 6-50R
receptacle, (which accepts 3-prong plugs.) For connection of
Lincoln equipment with NEMA 6-50 Plug.
. ))&'+ &%*
"#%')&'&)+#. ))The
MAXTRAC® wire drive enhances performance, while the
replacement case, and many other upgrade options that can
be installed in less then five minutes aid in the serviceability.
"'D;H7)A>>";FIncludes: 2 polished U
groove drive rolls, outer wire guide and inner wire
guide for solid core wire. (Used on LN-25 Pro)
"'D;H7)A>>";FIncludes: 2 polished U
groove drive rolls, outer wire guide and inner wire
guide for solid core wire. (Used on LN-25 Pro)
-%+S
"'D;H7)A>>";FIncludes: 2 V groove drive
rolls and inner wire guide for Steel Wires. (Used on
LN-25 Pro)
"#% - Includes internal contactor for across the arc opera-
tion (no control cable). Provides “cold” electrode until gun trigger is
pressed. Includes gas solenoid.
" #%5DAEEF:7D5.;D77767D
Portable, lightweight, compact CC/CV unit for flux-cored and MIG
welding. Includes Gas Solenoid, adjustable flow meter and internal
contactor. For 10-15 lb. (4.5-6.8kg) spools.
Magnum Gun and Magnum Gun Connector Kit are required for gas-
shielded welding. Innershield Gun is required for gasless welding.
" Magnum 350 Innershield Gun
" Magnum 300 MIG Gun (for LN-25)
" Magnum 300 MIG Gun (for LN-15, Includes Connector Kit)
" Connector Kit (for LN-15, K470-2)
" Gun Receiver Bushing (for LN-15 & K126-2)
"$39@G?*[*BAA>G@
Hand held semiautomatic wire feeder. Requires SG Control Module
and Input Cable.
"*[A@FDA>$A6G>7AD$39@G?*BAA>G@
The Interface between the power source and the spool gun.
Provides control of the wire speed and gas flow. For use with a
spool gun.
" @BGF34>7 (For SG Control Module)
For Lincoln engine power sources with 14-pin MS-type connection,
separate 115V NEMA receptacles and output stud connections.
%AF7 See Wire Feeder IM manuals for appropriate Drive Roll and
Guide Tubes.
+ &'+ &%*
"'DA+AD5:S'+-+ [+AD5:
Air Cooled 200 amp torch (2 piece) equipped with valve for gas flow
control. 25 ft. (7.6m) length.
"'$39@G?'3DFE";F8AD'+-+ +AD5:
Magnum Parts Kit provides all the torch accessories you need to
start welding. Parts kit provides collets, collet bodies, a black cap,
alumina nozzles and tungstens in a variety of sizes, all packaged in
an easy to carry reclosable sack.
"AAF?BFDA>S
"3@6?BFDA>S
"'D75;E;A@+ )736K'3=AD+
" @H7DF75S-+&@7'3=T'35=397
AD+
'#*$[,++ %
"'DAGF
Cuts mild steel using the 3-phase AC generator power from the
engine driven welder. Accepts 3-phase or 1-phase input power.
Requires the K1816-1 Full KVA adapter kit, if connected for 1-phase
input power.