Filter
Top Products
OPERATI
BEFORE STARTLING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 10)
. The engine inyourtractor has been shipped,fromthe
factory, already filled withsummer weight oil.
- Check engine oil with tractoron level ground.
o Unthread and remove oilfill cap!dipstick;wipe oil off°
Reinsertthe dipstickintothe tube and rest oilfill cap on
thetube. Do notthread the cap ontothetube. Remove
and read oil level° If necessary, add oil until "FULL"
mark on dipstick isreached. Do not overfill
o For cold weather operation you should change oilfor
easier starting (See OIL VISCOSITY CHART' inthe
Customer Responsibilitiessectionof this manual).
° To change engine oil, seethe Customer Responsibili-
ties section inthis manual.
.ENGINE OIL
FILL CAP/DIPSTICK
FIG. 10
ADD GASOLINE
= Fill fuel tank. Use fresh, clean, regular unleaded
gasoline with a minimum of 87 octane.. (Use of leaded
gasoline will increase carbon and lead oxide deposits
and reduce valve life)o Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
IMPORTANT; WHEN OPERATING IN TEMPERATURES
BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP INSURE GOOD COLD WEATHER
STARTING°
WARNING: Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation of
acids during storage° Acidic gas can damage the fuel
system of an engine while in storage. To avoid engine
problems, the fuel system should be emptied before stor-
age of 30 days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and carburetor are
empty. Use fresh fuel next season. See Storage instruc-
tions for additional information. Never use engine or
carburetor cleaner products in the fuel tank or permanent
damage may occur.
I_ CAUTION: Fill to bottom of gas tank
filler neck. Do not overfill. Wipe offany
spilled oil or fuel Do not store, spill or
use gasoline near an open flame.
TO START ENGINE (See Fig. 6)
When starting engine for the firsttime or ifengine has run
out of fuel, itwill take extra cranking time to move fuel from
the tank to the engine.
° Depress clutch/brake pedal and set parking brake°
• Place motion control lever in neutral (N) position.
° Move attachment clutch to "DISENGAGED" position.
• Pull choke controt out to choke (1\I) position for cold
engine start. For warm engine start do not use choke
control.
• Move throttle controlto midway between fast (,_) and
slow (,II) positions°
• lnsert key intoignitionand turn keyclockwise to"START"
positionand release key as soon as engine starts. Do
not run starter continuously for more than fifteen
seconds per minute. If engine does not start after
several attempts, move throttle control to fast (,_)
position, wait a few minutes and try again.
• When engine starts, slowly push choke control in.
° Move throttle control to fast (,_) position..
° Allow engine to warm up for a few minutes before
engaging drive or attachments.
IMPORTANT= COLD STARTING FOR HYDRO (BELOW
40 F) - AFTER STARTING ENGINE AND BEFORE
DR|VING, LET TRANSMISSION WARM UP FOR (1)
MINUTE BY PLACING MOTION CONTROL LEVER IN
NEUTRAL AND RELEASING CLUTCH/BRAKE PEDAL,.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32°F), the carburetor fuei mixture
may need tobe adjustedfor best engine performance. See
"TO ADJUST CARBURETOR" in the Service and Adjust-
ments section of this manual°
'15