Filter
Top Products
2 © SprayTECH. All rights reserved.
Important Safety Information · Read all safety information before
operating the equipment. SAVE THESE INSTRUCTIONS.
English
This symbol indicates a hazardous situation, which, if not
not avoided could result in death or serious injury.
To reduce the risks of fire or explosion, electrical shock
and the injury to persons, read and understand all
instructions included in this manual. Be familiar with the
controls and proper usage of the equipment.
HAZARD: EXPLOSION HAZARD DUE TO
INCOMPATIBLE MATERIALS
Will cause property damage or severe injury.
PREVENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such as bleach,
mildewcide, methylene chloride and 1,1,1 - trichloroethane. They
are not compatible with aluminum.
• Contact your coating supplier about the compatibility of material
with aluminum.
HAZARD: GENERAL
Can cause severe injury or property damage.
PREVENTION:
• Read all instructions and safety precautions before operating any
equipment.
• Follow all appropriate local, state, and national codes governing
ventilation, re prevention, and operation.
• The United States Government Safety Standards have been
adopted under the Occupational Safety and Health Act (OSHA).
These standards, particularly Part 1910 of the General Standards
and Part 1926 of the Construction Standard should be consulted.
• Use only manufacturer authorized parts. User assumes all risks
and liabilities when using parts that do not meet the minimum
specications and safety devices of the manufacturer.
• Before each use, check all hoses for cuts, leaks, abrasion or
bulging of cover. Check for damage or movement of couplings.
Immediately replace the hose if any of these conditions exist.
Never repair a hose. Replace it with an identical replacement hose.
• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
• Never aim the spray gun at any part of the body.
HAZARD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite. Property
damage and/or severe injury can occur.
PREVENTION:
• Exhaust and fresh air introduction must be provided
to keep the air within the spray area free from
accumulation of ammable vapors.
• Turbine contains sparking parts. Turbine must
be placed in a well ventilated area at maximum
distance from the spray area.
• Avoid all ignition sources such as static electricity, open ames,
pilot lights, hot objects, cigarettes, and sparks from connecting
and disconnecting power cords and working light switches.
• Use extreme caution when using materials with a ashpoint below
70° F (21°C). A uid’s ashpoint is the temperature at which
vapors from the uid could ignite if exposed to a ame or spark.
• Fire extinguishing equipment must be present and in working
order.
• The power cord must be connected to a grounded circuit.
• Follow the material and solvent manufacturer’s safety precautions
and warnings.
HAZARD: HAZARDOUS VAPORS
Paints, solvents, insecticides, and other materials can be
harmful if inhaled or come in contact with the body. Vapors
can cause severe nausea, fainting, or poisoning.
PREVENTION:
• Use a respirator or mask if vapors can be inhaled.
Read all instructions supplied with the mask to be
sure it will provide the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating manufacturer.
HAZARD: SKIN BURN INJURY
Heated parts can cause severe skin burn injury.
PREVENTION:
• Quick disconnect ttings on the hose and spray gun become
hot during use. Avoid skin contact with quick disconnect ttings
when they are hot. Allow quick disconnect ttings to cool before
disconnecting the spray gun from the hose.
Grounding Instructions
This product must be grounded. In the event of an electrical short circuit,
grounding reduces the risk of electric shock by providing an escape
wire for the electric current. This product is equipped with a cord having
a grounding wire with an appropriate grounding plug. The plug must
be plugged into an outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING - Improper installation of the grounding plug can
result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect
the green grounding wire to either at blade terminal. The wire with
insulation having a green outer surface with or without yellow stripes is
the grounding wire and must be connected to the grounding pin.
Check with a qualied electrician or serviceman if the grounding
instructions are not completely understood, or if you are in doubt as
to whether the product is properly grounded. Do not modify the plug
provided. If the plug will not t the outlet, have the proper outlet installed
by a qualied electrician.
Grounded Outlet
Grounding Pin
Cover for grounded outlet box
IMPORTANT: Use only a 3-wire extension cord that has a 3-blade
grounding plug and a 3-slot receptacle that will accept the plug on
the product. Make sure the extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough
to carry the current the product will draw. An undersized cord
will cause a drop in line voltage resulting in loss of power and
overheating. A 12 gauge cord is recommended. If an extension cord
is to be used outdoors, it must be marked with the suffix W-A after
the cord type designation. For example, a designation of SJTW-A
would indicate that the cord would be appropriate for outdoor use.
NOTE: More than 100 feet of extension cord is not
recommended. Use more paint hose, not more
extension cord. Shorter extension cords will assure
maximum electrical power for proper operation.
Service
Should your spray system need service during the warranty period,
return your unit and the proof of purchase to the distributor where it was
purchased. At our option, the unit will be repaired or replaced. In a
continued commitment to improve quality, we reserve the right to make
component or design changes when necessary.
Uncontrolled Copy