Filter
Top Products
English
Cleaning the Spray Tip
1. Flush the gun with solvent immediately after the work is
completed.
2. Oil the sliding pins to prevent them from seizing up.
Should the spray tip become clogged,
reverse the spray tip with the lever and
pull the trigger. Once the obstruction
comes out of the spray tip, release the
trigger, reverse the spray tip back to the
spray pattern setting, and resume
spraying.
Do not attempt to clean the tip with your finger.
Do not use a needle or other sharp pointed instrument to
clean the tip. The hard tungsten carbide is brittle and can
be chipped.
Cleaning the Filter
Clean the filter with a brush dipped in solvent. Never poke the
filter with a sharp instrument.
Changing the Filter
1. Pull the trigger guard forward
so that it comes loose from
the handle.
2. Unscrew the handle from the
housing and remove the old
filter.
3. Slide the new filter, taper end
first, into the gun housing.
4. Replace the handle, washer
and spring. Screw the handle
into the housing until hand-
tight. Replace the trigger
guard.
Replacing the Valve Spring Unit
1. Unscrew the spray tip.
2. Lock the gun in the ON position and remove the diffuser
with a wrench
3. Unlock the gun.
4. Unscrew the nut
with a wrench
and remove the
retainer block.
5. Remove the
sliding pins with
care and store
them in a safe
place so they will
not be lost.
6. Drive the valve
spring unit
forward from the back of the retainer block. Use the
handle of a wooden hammer or similar soft tool to avoid
damaging the valve spring unit.
Gun Housing
Valve Spring
Unit
Sliding Pin
Nut
Retainer Block
Diffuser
NOTE: Replace the packing if the spray gun is
disassembled. Replace the sliding pins if they
are worn.
Gun Housing
Filter
Handle
WARNING
Choosing the Correct Spray Gun Filter
Use the proper gun filter based on the type of material being
applied as shown below.
Accessories
Part No.
Description
0297xxx RC Tip Assembly
0502xxx Replacement Core, RC Tip
0297078 Tip Guard, RC Tip (11/16”)
0297070 Tip Guard, RC Tip (7/8”)
0291004 Hose, Whip End, 3' x 3/16"
0291003 Hose, Whip End, 5’ x 3/16”
0291002 Hose, Wireless, 25’ x 1/4"
0291000 Hose, Wireless, 50’ x 1/4"
0093896 Hose Connector, 1/4” x 1/4”M
0088154 Pressure Gauge
0152001 Power Roller Gun Attachment
0152308 9" Roller Cover, 3/8” Nap
0152307 9" Roller Cover, 1/2” Nap
0152309 9" Roller Cover, 3/4” Nap
0152310 9" Roller Cover, 1-1/4” Nap
0152235 12" Roller Cover, 1/2" Nap
0152236 12" Roller Cover, 3/8" Nap
0152237 12" Roller Cover, 3/4" Nap
0152238 12" Roller Cover, 1-1/4" Nap
0152700 Adapter, Power Roller Extension
0270145 G-10 Four Finger Airless Spray Gun (no tip)
0093930 Anti-Seize Compound
0152909 R-10 Telescoping Roller, 9", 3/8" Nap
0152900 R-10 Telescoping 12" Roller, 3/8" Nap
0502007 G-10 Four Finger Airless Spray Gun with 517
Reversible Tip
0502011 G-10 Two Finger Airless Spray Gun (no tip)
0502009 G-10 Two Finger Airless Spray Gun with 517
Reversible TIp
0270214 G-10 Four Finger Spray Pack with 50’ x 1/4”
airless hose
0502012 G-10 Two Finger Spray Pack with 50” x 1/4”
Airless Hose
Part no. Application Filter
type
Mesh
number
Color of
Filter
body
0089960 Synthetic resin,
enamels, clean
varnishes, stains
azures
Extrafine 0.084 mm red
0089959 Base coat enamels,
primer enamels,
fillers, marking paints,
textured enamels
Fine 0.140 mm yellow
0089958 Emulsions,
latex paints,
acrylic paints
Medium 0.315 mm white
0089957 Filler paints,
large area surfaces
Coarse 0.560 mm green
© SprayTECH Corporation. All rights reserved. 9