Filter
Top Products
3
GB
HAZARD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite. Severe
injury and/or property damage can occur.
PREVENTION:
• Provide extensive exhaust and fresh air introduction
to keep the air within the spray area free from
accumulation of ammable vapors.
• Avoid all ignition sources such as static electricity
sparks, electrical appliances, ames, pilot lights, hot
objects, and sparks from connecting and disconnecting
power cords or working light switches.
• Plastic can cause static sparks. Never hang plastic
to enclose spray area. Do not use plastic drop cloths
when spraying ammable materials.
• Do not smoke in spray area.
• Fire extinguisher must be present and in good working
order.
• Power cord must be connected to a grounded circuit
(electric units only).
• Follow material and solvent manufacturer’s warnings
and instructions. Be familiar with the coating material’s
MSDS sheet and technical information to ensure safe
use.
• Use extreme caution when using materials with a
ashpoint below 70° F (21° C). Flashpoint is the
temperature that a uid can produce enough vapors to
ignite.
HAZARD: EXPLOSION HAZARD DUE TO
INCOMPATIBLE MATERIALS
Will cause severe injury or property damage.
PREVENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such
as methylene chloride and 1,1,1 - trichloroethane.
They are not compatible with aluminum and may
cause an explosion. If you are unsure of a material’s
compatibility with aluminum, contact your coating’s
supplier.
HAZARD: HAZARDOUS VAPORS
Paints, solvents, insecticides, and other materials
can be harmful if inhaled or come in contact with
body. Vapors can cause severe nausea, fainting, or
poisoning.
PREVENTION:
• Use a respirator or mask if vapors can be inhaled.
Read all instructions supplied with the mask to be sure
it will provide the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating
manufacturer.
HAZARD: SKIN BURN INJURY
Heated parts can cause severe skin burn injury.
PREVENTION:
• Quick disconnect ttings on the hose and spray gun
become hot during use. Avoid skin contact with quick
disconnect ttings when they are hot. Allow quick
disconnect ttings to cool before disconnecting the
spray gun from the hose.
Earthing Instructions
PE
Electric models must be earthed. In the event of an
electrical short circuit, earthing reduces the risk of electric
shock by providing an escape wire for the electric current.
This product is equipped with a cord having an earthing
wire with an appropriate earthing plug. The plug must be
plugged into an outlet that is properly installed and earthed
in accordance with all local codes and ordinances.
DANGER — Improper installation of the earthing plug
can result in a risk of electric shock. If repair or
replacement of the cord or plug is necessary, do not
connect the green earthing wire to either blade
terminal. The wire with insulation having a green outer
surface with or without yellow stripes is the earthing
wire and must be connected to the earthing pin.
Check with a qualied electrician or serviceman if the earthing
instructions are not completely understood, or if you are in doubt as to
whether the product is properly earthed. Do not modify the plug provided.
If the plug will not t the outlet, have the proper outlet installed by a
qualied electrician.
Caution – The power cord for this equipment acts as an
emergency stop/emergency switching off device. The
power cord must be placed near an easily accessible,
unobstructed socket-outlet.
Work or repairs at the electrical equipment:
These may only be carried out by a skilled electrician. No liability is
assumed for incorrect installation.
Power cord replacement must be performed by the manufacturer, its
service agent, or a similarly qualied person.
Operating Temperature
This equipment will operate correctly in its intended ambient, at a
minimum between +10°C and +40°C.
Relative Humidity
The equipment will operate correctly within an environment at 50% RH,
+40°C. Higher RH may be allowed at lower temperatures.
Measures shall be taken by the Purchaser to avoid the harmful effects of
occasional condensation.
Altitude
This equipment will operate correctly up to 3000 m above mean sea level.
Transportation and Storage
This equipment will withstand, or has been protected against,
transportation and storage temperatures of -25°C to +55°C and for short
periods up to +70°C.
It has been packaged to prevent damage from the effects of normal
humidity, vibration and shock.
i
A list of the materials used in the construction of the
equipment will be made available on request to validate
compatibility with the coating materials to be used.
PE