Filter
Top Products
V !&
6#;?5@5;:@41/;>0/81->;2@41?<5::5:3-//1??;>E If
you lose control, the cord may be cut or snagged and
your hand or arm may be pulled into the spinning
accessory.
7!1B1>8-E@41<;C1>@;;80;C:A:@58@41-//1??;>E
4-?/;91@;-/;9<81@1?@;< The spinning accessory
may grab the surface and pull the power tool out of
your control.
8;:;@>A:@41<;C1>@;;8C4581/->>E5:35@-@E;A>
?501 Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
9 %13A8->8E/81-:@41<;C1>@;;8\?-5>B1:@?The motorʼs
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
: ;:;@;<1>-@1@41<;C1>@;;8:1->28-99-.81
9-@1>5-8? Sparks could ignite these materials.
; ;:;@A?1-//1??;>51?@4-@>1=A5>185=A50/;;8-:@?
Using water or other liquid coolants may result in
electrocution or shock.
< ;:;@A?1'E<128->5:3/A<C4118?;:@45?@;;8
Using inappropriate accessories can result in injury.
= 8C-E?A?1?5014-:081'534@1:@414-:081?1/A>18E
The side handle should always be used to maintain
control of the tool at all times.
> (?1/8-9<?;>-:;@41><>-/@5/-8C-E@;?1/A>1-:0
?A<<;>@@41C;>7<51/1@;-?@-.81<8-@2;>9 Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
5/7.-/7-:0%18-@10*->:5:3?
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool to
be forced in the direction opposite of the accessoryʼs rotation
at the point of the binding. For example, if an abrasive wheel is
snagged or pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the surface of
the material causing the wheel to climb out or kick out. The
wheel may either jump toward or away from the operator,
depending on direction of the wheelʼs movement at the point
of pinching. Abrasive wheels may also break under these
conditions. Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below:
- -5:@-5:-25>93>5<;:@41<;C1>@;;8-:0<;?5@5;:
E;A>.;0E-:0->9@;-88;CE;A@;>1?5?@75/7.-/7
2;>/1?8C-E?A?1-AD585->E4-:08152<>;B50102;>
9-D59A9/;:@>;8;B1>75/7.-/7;>@;>=A1>1-/@5;:
0A>5:3?@->@A< The operator can control torque reaction
or kickback forces, if proper precautions are taken.
. !1B1><8-/1E;A>4-:0:1->@41>;@-@5:3-//1??;>E
Accessory may kickback over your hand.
/;:;@<;?5@5;:E;A>.;0E5:@41->1-C41>1<;C1>
@;;8C5889;B15275/7.-/7;//A>? Kickback will
propel the tool in direction opposite to the wheelʼs
movement at the point of snagging.
0 (?1?<1/5-8/->1C41:C;>75:3/;>:1>??4-><
1031?1@/B;50.;A:/5:3-:0?:-335:3@41
-//1??;>E Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss
of control or kickback.
1;:;@-@@-/4-?-C/4-5:C;;0/->B5:3.8-01;>
@;;@410?-C.8-01 Such blades create frequent
kickback and loss of control.
'(%&53
Slider switch
Cord
Tool free guard
Side handle (3 positions)
Spindle lock button
&& ,
*->:5:3 To prevent accidental operation, turn off and
unplug tool before performing the following operations.
Failure to do this could result in serious personal injury.
AD585->E4-:081
An auxiliary 3 position handle is furnished with your grinder.
It can be screwed into either side or the top of the gear case
housing.
*->:5:3'45?4-:081?4;A80.1A?10-@-88@591@;
9-5:@-5:/;9<81@1/;:@>;8;2@41@;;8
//1??;>51?
It is important to choose the correct guards, backing pads
and flanges to use with grinder accessories.
;A:@5:33A->053-:0
53A>1 Open the guard latch and align the lugs
on the guard with the slots on the gear case cover
Push the guard down until the guard lugs engage and
rotate freely in the groove on the gear case hub.
With the guard latch open, rotate the guard into the
desired working position. The guard body should be
positioned between the spindle and the operator to
provide maximum operator protection.
53A>1 Close the guard latch to secure the guard
on the gear case. You should not be able to rotate the
guard by hand when the latch is closed. Do not operate
the grinder with a loose guard or the guard latch in
open position.
To remove the guard, open the guard latch, rotate the
guard so that the lugs and slots are aligned and pull up
on the guard.
(%'%&',!&'%('"!&
"%"#%'"!&