Filter
Top Products
12
RECOMMENDED MAINTENANCE
NOTE: Disconnect machine from power source before
performing any maintenance.
LUBRICATION
All bearings are sealed and permanently lubricated. No
further lubrication is needed.
ROUTINE INSPECTION
It is recommended that you periodically inspect your
spindle sander as a precautionary action. During this
time, check for the following:
• Inspect all hardware, fittings and fasteners that may
have loosened due to vibration and re-tighten as
needed.
• Check for dust and/or wood particles that may have
accumulated on or in the machine. Check all dust
collection fittings – re-tighten as needed.
• Inspect the ON/OFF SWITCH for damage before each
use. Periodically inspect the power cord and plug for
damage. If necessary replace the power cord and the
plug at the first signs of visible damage.
• Check all table inserts, spindles and sanding sleeves
for damage and replace if necessary.
REPLACING THE SANDING
SLEEVES
Make sure that the switch is in “OFF"
position and that the power cord is
unplugged.
NOTE: Reverse threads are used to attach the spindle
to the machine.
• Remove the table insert by lifting it up and over the
sanding spindle.
• Using two 17 mm wrenches, as shown in Figure 4
(page 8), loosen the spindle by turning it clockwise.
• With the 17 mm wrench still positioned on the spindle
seat, unscrew (clockwise) the spindle with your hand
and remove.
• To remove the ¼", ½", or
5
/8" sanding sleeve, loosen
the Phillips head screw at the bottom of the spindle
and pull the sanding sleeve and spindle apart.
To remove the 1 ½" or 2" sanding sleeve, use the
supplied 12 mm wrench to loosen (clockwise) the nut
at the top of the spindle. Pull the sanding sleeve and
spindle apart.
• To install a new sanding sleeve, follow the directions
on page 8 (INSTALL SANDING SLEEVES ONTO
SPINDLES).
ACCESSORIES
A complete line of accessories is available from your DELTA
®
Supplier, DELTA
®
Factory Service Centers, and
DELTA
®
Factory Service Centers, and DELTA
®
Authorized Service Centers. Please visit our Web Site www.
DeltaMachinery.com for an online catalog or for the name or your nearest supplier.
Since accessories other than those offered by DELTA
®
have not been tested with this product,
use of such accessories could be hazardous. For safest operation, only DELTA
®
recommended
accessories should be used with this product.
Five Year Limited New Product Warranty
DELTA
®
will repair or replace, at its expense and at its option, any new DELTA
®
machine, machine part, or machine accessory which in normal
use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a DELTA
®
factory service
center or authorized service station with proof of purchase of the product within five years and provides DELTA
®
with reasonable opportunity
to verify the alleged defect by inspection. For all refurbished DELTA
®
product, the warranty period is 180 days. DELTA
®
will not be responsible
for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone
other than an authorized DELTA
®
service facility or representative. Under no circumstances will DELTA
®
be liable for incidental or consequential
damages resulting from defective products. Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This warranty is DELTA
®
’s sole warranty and sets forth the customer’s exclusive remedy,
with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are
expressly disclaimed by DELTA
®
. For further detail of warranty coverage and warranty repair information, visit www.DeltaMachinery.com or call
1-800-223-7278. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.
WARRANTY
To register your tool for warranty service visit our website at www.DeltaMachinery.com.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in the packaging, call the local company or see website for warranty
information.