Filter
Top Products
10
UNPACKING
(continued)
30" Fence versions (36-5000 and 36-5100)
Description Qty. Where used
M8 x 70mm Carriage bolt 1 Connect stand halves
M8 nylock nut 1 Connect stand halves
M6 x 72 mm Carriage bolt 4 Connect stand leg to stand
M6 lock nut 4 Connect stand leg to stand
M8 x 53mm axle pin 2 Wheels
M8 2 Wheels
M6 x 10mm Phillips head self tapping screw 16 Stand Panels
5/16-18 x 7/8" Hex screw w/spring washer 17 Wings to table 6, wing to wing 3,
rear rail 8
1/4-20
x 1/2" Hex Soc button head screw 6 Guid tube to rail
5/16-18 x 1 1/8" Flat head screw 8 Front rail to table and wings 8
5/16-18 hex flange nut 17 Wing to wing 3, rear rail 6, Front rail 8
Rail alignment gauge 1
52" Fence versions (36-5052 and 36-5152)
Description Qty. Where used
M8 x 70mm Carriage bolt 1 Connect stand halves
M8 nyloc nut 1 Connect stand halves
M6 x 72mm Carriage bolt 4 Connect stand leg to stand
M6 lock nut 4 Connect stand leg to stand
M8 x 53mm axle pin 2 Wheels
M8 nylock nut 2 Wheels
M6 x 10mm Phillips head self tapping screw 16 Stand Panels
5/16-18 x 7/8" Hex Head screw w/spring washer 15 Wings to table 6, rear rail 6,
Wing to wood tabl
e 3
5/16-18 Flat washer 3 wing to wood table
1/4-20 x 1/2" Hex Soc button head screw 8 Guide tube to rail
5/16-18 x 1 1/8" Flat head screw 6 Front rail to table and wings 6
5/16-18 Hex flange nut 13
Rear rail 4, Front rail 6, wing to wood
1/4-20 X 1 1/2" Hex Head Screw 6 Rails to wood table rear
1/4" Flat washer 12 Rails to wood table
1/4-20 hex nuts 12 Rails to wood table
#8 x 3/4" Phillips head self tapping screw 8 legs to table
#10-32 x 1 1/4" screws 4 legs to table
#1
0 flat washer 4 legs to table
#10-32 hex nuts 4 legs to table
Rail alignment gauge 1
HARDWARE PACKAGES
** Hardware supplied will accommodate the 36-5052 model saw that uses the most hardware.
M8 spring washer 1 Connect stand halves
M8 spring washer 1 Connect stand halves
Item #
Parts List
Item #
Parts List
153
155
154
144
145
151
155
146
58
35
19
16
190
153
155
154
144
145
151
155
146
58
35
19
16
190
183
184
185
182
180
179
181
*
Hardware supplied will accommodate the 36-5000 model saw that uses the most hardware.
**
*
Conical star washer 5/16” 1 On 1 screw for the front rail going into table
for electrical ground.
191
Flat star washer 5/16” 1 On 1 screw for the rear rail going into table
for electrical ground.
192
Conical star washer 5/16” 1 On 1 screw for the front rail going into table
for electrical ground.
191
Flat star washer 5/16” 1 On 1 screw for the rear rail going into table
for electrical ground.
192
table 3,
193
nylock nut
1/4-20 X 1 1/2" Flat Head Screw 6 Rails to wood table front
186