Filter
Top Products
9
English
OPERATION
WARNING: To reduce the risk of injury, turn unit off and disconnect machine
from power source before installing and removing accessories, before adjusting or
changing set-ups or when making repairs. An accidental start-up can cause injury.
WARNING: Before using the saw, verify the following each and every time:
• ALWAYS wear proper eye, hearing and respiratory equipment.
• Blade is tight.
• Bevel angle and height lock knobs are tight.
• If ripping, ensure fence lock lever is tight and fence is parallel to the blade.
• If crosscutting, miter gauge knob is tight.
• The blade guard assembly is properly attached and the anti-kickback assembly is
functioning.
• ALWAYS inspect the blade guard assembly and riving knife for proper alignment, operation
and clearance with saw blade.
• ALWAYS make sure both guards are in the down position in contact with the table before
operating.
WARNING: To reduce the risk of serious personal injury, have push stick ready to use
before starting cut.
Failure to adhere to these common safety rules can greatly increase the likelihood of injury.
WARNING: To reduce the risk of injury, turn unit off and disconnect machine from
power source before installing and removing accessories, before adjusting or changing set-
ups or when making repairs. An accidental start-up can cause injury.
WARNING: Before connecting the table saw to the power source or operating the saw,
always inspect the blade guard assembly and riving knife for proper operation alignment and
clearance with saw blade. Personal injury may result.
WARNING: Ripping or crosscutting may cause saw to tip over while operating. Make sure
saw is securely mounted to a stable surface.
WARNING: Never use the fence and miter gauge together. This may cause a kickback
condition and injure the operator.
CAUTION: If this saw makes an unfamiliar noise or if it vibrates excessively, cease
operating immediately, turn unit off and disconnect from power source until the problem has
been located and corrected. Contact a D
EWALT factory service center, a DEWALT authorized
service center or other qualified service personnel if the problem cannot be found.
CAUTION: The proper throat plate must be in place at all times to reduce the risk of a
thrown workpiece and possible injury.
There are two basic types of cutting with table saws: ripping and crosscutting. Regardless
of material, man made or natural wood, the distinction between ripping and crosscutting
is as follows: Ripping is cutting to a different width (usually with the grain) and crosscutting
describes cutting material across the shorter dimension (usually against the grain).
WARNING: When ripping, always use the fence to provide a guide for the material and
blade guard assembly to protect against a kickback situation.
WARNING: Never perform any cutting operation free hand. Never perform plunge cutting.
CAUTION: When crosscutting, always use the miter gauge.
The riving knife provided with this saw is marked as follows (Fig. 27):
0.087" (2.2mm) THICK RIVING KNIFE. ONLY USE FOR 10" (254mm) Ø BLADE WITH
0.094" (2.4 mm) MIN. KERF WIDTH AND 0.067" (1.75mm) MAX. BODY THICKNESS.
FIG. 27
All DEWALT blade body thickness and kerf widths are provided at www.dewalt.com.
If a different blade is used and the body thickness
FIG. 28
and kerf width dimensions are not provided, use the
following procedure to determine the correct riving
knife thickness:
1. Measure the body thickness of the blade.
2. Make a shallow cut in scrap material and measure
the kerf width.
3. Select the riving knife (Fig. 28).
4. Slide the riving knife through the shallow cut
made in step 2 to confirm the correct riving knife
has been selected. The riving knife should not
bind or drag through the cut (Fig. 28).
IMPORTANT: If any dragging or binding of the
material is encountered as it reaches the riving knife,
turn unit off and disconnect machine from power
source. Repeat steps 1–4 to make the proper riving
knife selection before attempting another cut.
Kickback
Kickback is a dangerous condition! It is caused by the workpiece binding against the blade.
The result is that the workpiece can move rapidly in a direction opposite to the feed direction.
During kickback, the workpiece could be thrown back at the operator. It can also drag
the operator’s hand back into the blade if the operator’s hand is at the rear of the blade. If
kickback occurs, turn the saw OFF and verify the proper functioning of the riving knife, anti-
kickback assembly and blade guard assembly before resuming work.
WARNING: See Additional Safety Rules for Table Saws and follow all warnings
provided regarding KICKBACK.