Elektra Beckum TKHS 315 (AUS) Saw User Manual


 
6
ENGLISH
A
Hazard generated by insuffi-
cient personal protection gear!
Wear hearing protection.
Wear safety glasses.
Wear dust mask.
Wear suitable work clothes. When work-
ing outdoors wearing of non-slip shoes is
recommended.
A
Risk of injury by inhaling wood
dust!
Dust of certain timber species (e.g. oak,
beech, ash) can cause cancer when
inhaled: work only with a suitable dust
collector attached to the saw.
A
Hazard generated by modifica-
tion of the machine or use of parts
not tested and approved by the equip-
ment manufacturer!
Assemble tool in strict accordance with
these instructions.
Use only parts approved by the equip-
ment manufacturer.
Use only tools (saw blades) conforming
to EN 847-1:1997.
Do not make changes to any of the
parts.
Use only matching saw blades and riving
knives.
A
Hazard generated by tool
defects!
Keep tool and accessories in good
repair. Observe the maintenance
instructions.
Before any use check tool for possible
damage: before operating the tool all
safety devices, protective guards or
slightly damaged parts need to be
checked for proper function as specified.
Check to see that all moving parts work
properly and do not jam. All parts must
be correctly installed and meet all condi-
tions necessary for the proper operation
of the tool.
Damaged protection devices or parts
must be repaired or replaced by a quali-
fied specialist. Have damaged switches
replaced by a service centre. Do not
operate tool if the switch can not be
turned ON or OFF.
Keep handles free of oil and grease.
4.3 Symbols used through-
out these instructions
A
Danger!
Indicates risk of personal
injury or severe material dam-
age.
B
Risk of electric shock!
Risk of personal injury by elec-
tric shock.
c
Drawing-in/trapping hazard!
Risk of personal injury by body
parts or clothing being drawn
into the rotating saw blade.
A
Caution!
Risk of material damage.
3
Note:
Additional information.
4.4 Safety devices
Riving knife
The riving knife (43) prevents the work-
piece from being caught by the rising
teeth of the saw blade and being thrown
against the operator.
Always have the riving knife installed
during operation.
Blade guard
The blade guard (44) protects against
unintentional contact with the saw blade
and from chips flying about.
Always have the blade guard installed
during operation.
Push stick
The push stick (45) serves as an exten-
sion of the hand and protects against
accidental contact with the saw blade.
Always use the push stick if the distance
between saw blade and rip fence is less
than 120 mm.
Guide the push stick at an angle of 20°
… 30° against the saw table's surface.
When the push stick is not used, it can
be hung to the holder (46) provided.
Replace the push stick if damaged.
Handle for push block
To be affixed to a suitable board. For the
safe guiding of small stock.
Steplessly adjustable bevel tilt from
90° to 45°.
Stepless depth of cut setting to
85 mm.
An undervoltage relay prevents the
machine from starting up when
power is restored after a power fail-
ure.
All operating elements are located
at the machine's front.
Robust sheet metal construction
with galvanized saw table.
ON/OFF switch
To start = press green switch button
(47).
To stop = press red switch button
(48).
3
Note:
In the event of a power failure an
undervoltage relay is activated. This pre-
vents the starting of the machine when
the power is restored. To restart, the
green switch button must be actuated.
Setting device for saw blade tilt
The saw blade tilt can be steplessly set
by the handwheel (49) from 0° through
45°.
43 44
45
46
5. Special product features
6. Operating elements
47
48
49 50